Mec 2684ES Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 344

background image

Page 136

Speed Level Seres - Servce & Parts Manual

January 2019

Secton 9 - Troubleshootng - 3084ES Models

EZ-Cal Diagnostics

The EZ-Cal Diagnostics menu provides the ability to view and test individual circuits for irregularities.
Whether diagnosing a failure or testing functions during preventative maintenance, the Diagnostics
Menu provides a quick view at the inputs and outputs as registered by the GP400 Control Module and
the P600 Motor Control Module in real time. Using the EZ-Cal Flow Chart, compare ID number to this
menu for circuit identification and result. To reach DIAGNOSTICS menu from HELP;

Press the right arrow and scroll to DIAGNOSTICS and press ENTER.
Locate the desired sub menu and press ENTER.
Press the right arrow to scroll through the test points.

Note:

The ID number will not appear on the EZ-Cal display. It is shown in the Diagnostics Menu for
reference only.

Using the ID number, match specific personalities from the Diagnostic Flow Chart with this table for
additional information.

Press ESC to go back one level (necessary to change selection).

Selection

ID

EZ-Cal Readout

Explanation

2A

SYSTEM

2A-1

MODE

Current function message/s, press ENTER for additional information

2A-2

Supply

Indicates valve supply output on or off; should be ON

2A-3

Valve Supply

Regulated 12 volt signal output from Motor Controller to supply all 12 volt circuits

2A-4

Motor Volts

Real time motor voltage

2A-5

Motor 1

Real time motor amperage draw. Varies depending on load and motor speed.

2A-6

Temperature

Motor controller chassis temp. Error message “too Hot” at 75 C.

2A-7

Tilt

Current state of tilt as measured by Can-tilt angle transducer in degrees

2A-8

Tilted Y/N

Indicates tilted state. All motorized functions interlocked above @ height (15%
elevation)

2A-9

Height

Current state of platform elevation in %.

2A-10

Load

Current load on platform in %. (Over load option only)

2A-11

Overloaded Y/N

Platform overload status. (Over load option only)

2A-12

Last Moved

Not used

2A-13

Elevated Y/N

Shows platform elevation is above 15% (@ height setting). Elevated settings apply.

2A-14

Outrigger (leveling
function)

Press ENTER for outrigger sub categories.

SUB

CATEGORIES

2A-14a

O/R Retracted Y/N

Not used

2A-14b

O/R Extended Y/N

Not used

2A-14c

O/R Status

Current state of level will be displayed,

2A-14d

O/R Test Y/N

Not used

2B

PLATFORM

2B-1

Trigger ON/OFF

Current status of enable trigger; pulled =ON @ platform controls

2B-2

DLD

Position of Lift/Drive selector switch

2B-3

Joystick

Indicates % of stroke from center in real time. Direction not indicated here

2B-4

FWD/DWN OFF/ON

Status of Forward micro-switch Forward stroke of the joystick

2B-5

REV/UP OFF/ON

Status of Reverse micro-switch Reverse stroke of the joystick

2B-6

LEFT OFF/ON

Status of Left Steer switch

2B-7

RIGHT OFF/ON

Status of Right Steer switch

2B-8

Positrac Y/N

Status of rear wheel solenoids activation. Activated in high speed or elevated drive

2B-9

EMSp OFF/ON

Not used

•
•
•

«
...
141
142
143
144
145
...
»

Содержание 2684ES

























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2684ES

Бренд: MAHA Страницы: 45

Бренд: R. Beck Maschinenbau Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды