manualshive.com logo in svg

Measurement Computing PCIM-DAS1602/16, Руководство пользователя

На сайте manualshive.com вы можете бесплатно скачать руководство пользователя для измерительного устройства Measurement Computing PCIM-DAS1602/16. Этот мануал обеспечит вас всей необходимой информацией для эффективного использования устройства. Скачайте его прямо сейчас!

Поделиться
Скачать
background image

5.1.2 System Grounds and Isolation

There are three scenarios possible when connecting your signal source to your PCIM-DAS1602/16
board.  

1. The PCIM-DAS1602/16 and the signal source have the same (or common) ground. This signal

source can be connected directly to the PCIM-DAS1602/16.

2. The PCIM-DAS1602/16 and the signal source have an offset voltage between their grounds  (AC

and/or DC). This offset it commonly referred to a common mode voltage.  Depending on the
magnitude of    this voltage, it may or may not be possible to connect the PCIM-DAS1602/16
directly to your signal source. We will discuss this topic further in a later section.

3. The PCIM-DAS1602/16 and the signal source already have isolated grounds. This signal source

can be connected directly to the PCIM-DAS1602/16.

Which system do you have?
Try the following experiment. Using a battery powered voltmeter*, measure the voltage (difference)
between the ground signal at your signal source and at your PC. Place one voltmeter probe on the PC
ground and the other on the signal source ground. Measure both the AC and DC Voltages. 

*If you do not have access to a voltmeter, skip the experiment and take a look a the following three
sections. You may be able to identify your system type from the descriptions provided.

If both AC and DC readings are 0.00 volts, you may have a system with common grounds. However,
since voltmeters will average out high frequency signals, there is no guarantee. Please refer to the section
below titled Common Grounds.

If you measure reasonably stable AC and DC voltages, your system has an offset voltage between the
grounds category. This offset is referred to as a Common Mode Voltage. Please be careful to read the
following warning and then proceed to the section describing Common Mode systems.

WARNING

If either the AC or DC voltage is greater than 10 volts, do not connect the
PCIM-DAS1602/16 to this signal source. You are beyond the boards usable common
mode range and will need to either adjust your grounding system or add special
Isolation signal conditioning to take useful measurements.  A ground offset voltage of
more than 30 volts will likely damage the PCIM-DAS1602/16 board and possibly your
computer. Note that an offset voltage much greater than 30 volts will not only damage
your electronics, but it can also be hazardous to your health.

This is such an important point, that we will state it again. If the voltage between the
ground of your signal source and your PC is greater than 10 volts, your board will not
take useful measurements. If this voltage is greater than 30 volts, it will likely cause
damage, and can represent a serious shock hazard! In this case you will need to either
reconfigure your system to reduce the ground differentials, or purchase and install
special electrical isolation signal conditioning.

12

Содержание PCIM-DAS1602/16



















































Отзывы:

Нет отзывов

Похожие инструкции для PCIM-DAS1602/16

M-Audio Fast Track Ultra 8R Product Manual preview
Fast Track Ultra 8R
Бренд: M-Audio Страницы: 25
StarTech.com PCIIDE2 Instruction Manual preview
PCIIDE2
Бренд: StarTech.com Страницы: 14
Telit Wireless Solutions ME910X1 Hw Design Manual preview
ME910X1
Бренд: Telit Wireless Solutions Страницы: 56
Cognex CC24 Hardware Manual preview
CC24
Бренд: Cognex Страницы: 35
Hama 49075 Operating Instruction preview
49075
Бренд: Hama Страницы: 26
Gigabyte GV-R575SL-1GI User Manual preview
GV-R575SL-1GI
Бренд: Gigabyte Страницы: 32
KUARIO Smart Connector Installation Manual preview
Smart Connector
Бренд: KUARIO Страницы: 20
JARLTECH MSR 1218 SERIES Operation Manual preview
MSR 1218 SERIES
Бренд: JARLTECH Страницы: 18
Salto Design XS Installation Manual preview
Design XS
Бренд: Salto Страницы: 5
Farpointe Data P-300 Quick Start Manual preview
P-300
Бренд: Farpointe Data Страницы: 2
Farpointe Data Delta3-OSDP Quick Start Manual preview
Delta3-OSDP
Бренд: Farpointe Data Страницы: 2
Intellinet 500517 User Manual preview
500517
Бренд: Intellinet Страницы: 28
Lenovo Gemplus 41N3005 User Manual preview
Gemplus 41N3005
Бренд: Lenovo Страницы: 42
KTI Networks KF-310 Specification Sheet preview
KF-310
Бренд: KTI Networks Страницы: 1
SeaLevel ULTRA COMM+I.PCI 3055 User Manual preview
ULTRA COMM+I.PCI 3055
Бренд: SeaLevel Страницы: 22
Access Interfacing Solutions OCR-MC7 Quick Start Manual preview
OCR-MC7
Бренд: Access Interfacing Solutions Страницы: 2
Rosslare Mifare AS-B01 Hardware And Software Manual preview
Mifare AS-B01
Бренд: Rosslare Страницы: 50
Kanguru Media X-Change 2.0 User Manual preview
Media X-Change 2.0
Бренд: Kanguru Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды