background image

11

The Front Panel

The iconic front glass panel of the MX170 provides 

knobs and buttons to control the unit as well as an 

informational display and LED status lights that 

display the current mode.

Standby / On 

The red STANDBY / ON button toggles the MX170 

between on and standby mode. The STANDBY 

button will only work if the rear Power Switch 

(page 9) is on. When the unit is in standby 

mode, it can also be toggled on/off using the 

Remote Control or the browser interface. To use the 

on/off button in the top right corner of the browser 

interface, the MX170’s power management must 

be set to “Network” as opposed to “Deep sleep.” 

When the power management is set to Deep Sleep, 

the MX170 can not be woken up from the network 

interface.  The Power management can be setup 

under SETUP>System configuration>General 

setup>Power management. (For explanation of 

menu path notation see the box on page 14.)

The Input Knob

The Input Knob can be turned clockwise or 

counterclockwise to scroll through all the Inputs 

that are enabled in Setup. All Inputs are available by 

default. 

The Volume Knob

Turn this knob clockwise to raise the volume and 

go the other way to make it quieter. A maximum 

volume of 59% is the factory default, but this can 

be set to any value between 12% and 99% in Setup. 

A maximum volume prevents the MX170 from 

accidently sending higher signals than your situation 

permits. See “General Setup” on page 17.

The Arrow, Back and Select 

Buttons

These buttons are used to navigate menu screens 

and selections in the Trim menus. The arrows allow 

scrolling up  , down , left  , and right  , when 

those are menu choices. The SELECT button 

accepts an option and the BACK button returns to 

Figure 09–  MX170  Front  panel   

Содержание MX170





























Отзывы: