33
cylindrical microphone body below the Power On/Off
counterclockwise. Make sure the battery is installed
into the microphone, with the battery polarity match-
ing the diagram located inside the battery compart-
ment.
Note: If the microphone is not going to be used for a long
period of time, remove the battery.
3. Attach the hookup cable with connectors to the micro-
phone, making sure the cable end with the locking col-
lar attches to the microphone, and place the micro-
phone into the stand adapter, with the stand adapter
attached to a suitable microphone stand.
4. Switch the Power On to the Microphone by moving the
slide switch towards the color dot.
5. Press and hold the Front Panel SETUP Push-button for
approximately three seconds. The word SETUP will
appear on the Front Panel Display and the MAIN
SYSTEM SETUP Menu will appear on the Monitor/
TV screen. Refer to figure 12 on page 25.
5. Using the Up
or Down
directional push-buttons
select Speaker Setup on the On-Screen Menu, fol-
lowed by the SELECT Push-button on the Remote
Control. Refer to figure 21 on page 31.
Note: It is extremely important to have the room as quiet
as possible where the testing is occurring
(temporally switch off TVs, heating/cooling
equipment and radios, etc.) as this will yield the
most accurate results.
6. Using the Up
or Down
directional push-buttons
select AUTOCALIBRATE DELAYS on the On-Screen
Menu, followed by the SELECT Push-button on the
Remote Control. Refer to figure 23.
The Automatic Calibration Mode of the MHT200 will go
through many tests for each of the active Loudspeaker
Channels. The On-Screen Display will provide a status up-
date of the testing as it progresses. Refer to figure 24. The
On-Screen Display will indicate when testing is complete.
7. Continue next to the SUBWOOFER SETTINGS. If
you do not wish to perform SUBWOOFER SET-
TINGS adjustments at this time, proceed to the next
step.
8. Select EXIT from the SPEAKER SETUP Menu. The
MAIN SETUP Menu will reappear on the Monitor/TV
screen and select EXIT from the Menu. If you are sat-
isfied with the changes that you may have made, select
YES to save those changes or NO not to save them.
The MHT200 will then return to normal operation. Re-
fer to figure 13 on page 25.
SETUP, con’t
The Subwooofer Settings allow for optimizing perfor-
mance in the Home Theater System that relate to Room
Acoustics and Loudspeaker Characteristics. For most Sys-
tems the default setting will produce the best performance.
Refer to the Owner’s Manual that came with the Loud-
speaker, your Dealer and/or the manufacturer of the Loud-
speaker for recommendations. A chart on page 35 has been
provided to record the Subwoofer Settings.
Note: Before adjusting the SUBWOOFER SETTINGS, you
FIRST must have performed the SPEAKER SIZE,
SPEAKER TIME DELAY and SPEAKER LEVEL
Adjustments.
1. Press and hold the Front Panel SETUP Push-button ap-
proximately three seconds to enter the Setup Mode.
The word SETUP will appear on the MHT200 Front
Panel Display and the MAIN SYSTEM SETUP Menu
will appear on the Monitor/TV screen. Refer to figure
12 on page 25.
2. Using the Up
or Down
directional push-buttons
select Subwoofer Settings on the On-Screen Menu, fol-
lowed by the SELECT Push-button on the Remote
Control.
Note: The first time the SUBWOOFER SETTINGS is
accessed, the default settings will be indicated.
Mc Bass Mode
When a Home Theater System contains Loudspeakers that
are referred to as Large, the Bass Management Circuitry
will steer all the Low Frequency Sounds away from the
Subwoofer and to the Large Loudspeakers. With the MC
BASS MODE set to ON the Low Frequency Sounds are
sent to both the Large Loudspeakers and to the Subwoofer,
thus increasing the total low frequency output of the Home
Theater System. The default setting for the MC BASS
MODE is OFF. Refer to figure 25 on the next page and per-
form the following steps to switch it On.
3. Using the Up
or Down
directional push-buttons
select MC BASS MODE from the On-Screen Menu,
followed by pressing the Left
or Right
directional
push-buttons to active the circuit. Select EXIT on the
menu and the MAIN SYSTEM SETUP Menu will re-
appear on the Monitor/TV screen.
4. Continue to the next Subwoofer Setting, Sub Crossover.
If you do not wish to perform the remaining
SUBWOOFER SETTINGS Adjustments at this time,
proceed to the next step.
5. Select EXIT from the SPEAKER SETUP Menu. The
MAIN SETUP Menu will reappear on the Monitor/TV
screen and select EXIT from the Menu. If you are sat-
isfied with the changes that you may have made, select
How to Adjust the Subwoofer Settings
www.eskonline.nl