McIntosh C2600, Руководство пользователя

Страница: 4 / 32

4
ling the illumination of the Power
Output Meters on McIntosh Power
Amplifiers. A 3.5mm stereo mini
phone plug is used for connection
to the Power Control, Trigger and
PASSTHRU Outputs on the C2600.
Note: The Power Control, Trigger,
PASSTHRU and Data Connecting Cable is avail-
able from the McIntosh Parts Department:
Power Control, Trigger, PASSTHRU and Data
Cable Part No. 170202
Six foot, shielded 2 conductor, with 3.5mm stereo
mini phone plugs on each end.
Data Port Connectors
The C2600 Data Out Ports
send Remote Control Signals to
Source Components. A 3.5mm
stereo mini phone plug is used
for connection.
IR IN Port Connectors
The IR IN Port also uses a 3.5mm
stereo mini phone plug and allows
the connection of other brand IR
Receivers to the C2600.
RS232 Data Port Cable
The RS232 Data Cable is a 3.5mm stereo mini phone
plug to a subminiature DB 9 connector:
General Information and Connector Information
Connector and Cable Information
XLR Connectors
Below is the Pin configuration for the XLR Balanced
Input and Output Connectors on the C2600. Refer to
the diagrams for connections:
PIN 1: Shield/Ground
PIN 2: + Output
PIN 3: - Output
Power Control and Trigger Connectors
The C2600 Power Control Out, Trigger and PASSTH -
RU Output Jacks send Power On/Off Signals (+12
volt/0 volt) when connected to other McIntosh Com -
ponents. An additional connection is for control-
Data
Signal
N/C
Data
Ground
PIN 2 PIN 1
PIN 3
PIN 1
PIN 2
PIN 3
1. For additional connection information, refer to the
owner’s manual(s) for any component(s) connected
to the C2600 Tube Preamplifier.
2. The Main AC Power going to the C2600 and any
other McIntosh Component(s) should not be applied
until all the system components are connected
together. Failure to do so could result in malfunc-
tioning of some or all of the system’s normal opera-
tions. When the C2600 and other McIntosh Com -
ponents are in their Standby Power Off Mode, the
Microprocessor’s Circuitry inside each component
is active and communication is occurring between
them.
3. Balanced and Unbalanced Inputs and Outputs can
be mixed. For example, you may connect signal
sources to Unbalanced Inputs and send signals
from the Balanced Outputs. You can also use Bal-
anced and Unbalanced Outputs simultaneously,
connected to different Power Amplifiers.
4. The C2600 internal Digital to Analog Converter
Circuitry is designed to decode 2-channel PCM
(Pulse Code Modulation) and DSD (Direct Stream
Digital) Digital Signals. The Coaxial and Optical
Digital Audio Inputs are for PCM Digital Signals.
The Digital DIN and USB Audio Inputs are for
PCM and DSD Digital Signals. Other Digital Audio
Signal Format Types will cause the Audio Outputs
of the C2600 to be muted and the Front Panel Infor-
mation Display will indicate an error message.
5. Sound Intensity is measured in units called Deci -
bels and “dB” is the abbreviation.
6. The McIntosh C2600 is factory configured for im -
mediate use. It can also be customized to comple-
ment the components making up your system. Refer
to the C2600 “Setup Mode” starting on page 13 for
additional information.
General Information
Power
Control
Meter
Illumination
Control Ground
Main, Triggers 1-4
and PASSTHRU
7. The Remote Control Supplied with the C2600
Preamplifier is capable of operating other com-
ponents. For additional information go to www.
mcintoshlabs.com.
8. The IR Input, with a 3.5mm mini phone jack, is
configured for non-McIntosh IR sensors such as
a Xantech Model DL85K Kit. The signal from a
connected External IR Sensor will have priority
over the signal from the Front Panel IR Sensor.
9. When discarding the unit, comply with local rules
or regulations. Batteries should never be thrown
away or incinerated but disposed of in accordance
with the local regulations concerning battery
disposal.
10. For additional information on the C2600
and other McIntosh Products please visit
the McIntosh Web Site at www.mcintosh -
labs.com.
IR Data
Control
Ground
N/C
PIN 1
PIN 6
PIN 5
PIN 9
Data In
(DB9-pin2)
Ground
(DB9-pin5)
Data Out
(DB9-pin3)
DB9
(male connector)