manualshive.com logo in svg

McElroy SmartFab 125, Руководство оператора

Поделиться
Скачать
McElroy SmartFab 125 Скачать руководство пользователя страница 23

Inspect Melt

Quickly inspect the heated parts to make sure all surfaces have 
been melted properly.
If melt is not complete, cut off melted pipe end. Use a new fitting 
and repeat preparation and heating process.

TX04869-12-14-15

Remove Heater

Open the carriage completely. Quickly retract the heater. 

TX04868-12-14-15

Heating the Pipe and Fitting

Close the carriage until the heater stops make contact with the jaw frames.

IMPORTANT:

 Do not force the pipe and fitting onto the heater. Allow the 

pipe and fitting to melt onto the heater. Forcing the pipe and fitting onto 
the heater will damage the machine or create a questionable melt pattern.
Heating time starts when the pipe and fitting are fully inserted onto the 
heater adapters.
Heat the fitting and pipe for the pipe manufacturer or joining standard's 
specified period of time.

TX04867-12-14-15

Fusion Procedure

4 - 4

CD0

1446-1

2-0

1-1

5

CD0

144

7-1

2-0

1-1

5

CD0

1448-1

2-0

1-1

5

Heater Stops

Inspect Melt

Содержание SmartFab 125

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды