background image

ENGLISH - 5

Harness

The harness is equipped with a fasten-release 
mechanism. The harness enables the operator to support 
the machine during use (see “

Safety precautions

”, 

B7

). 

Before fastening the machine to the strapping, adjust the 
bandolier belt so that the fasten/release device is about 
15 cm above your waist. Using the blade, fasten the 
machine to the buckle using the hole nearest your body.

Preparation of the mixture

• To obtain the best mixture, pour the oil into an approved 

container first, followed by the gasoline, and shake the 
container well (every time you take fuel out of it).

• Be careful not to spill the gasoline.
• The characteristics of the mixture tend to deteriorate in 

time, so you should only prepare as much mixture as 
you are going to need (the use of deteriorated fuel can 
seriously damage the engine).

Filling the tank

• Fill the tank in a well-ventilated place.
• Place the machine on a solid flat surface so that it 

cannot tip over, with the cap on the tank facing upward.

• Clean the area around the fuel cap before removing it, 

to prevent any impurities from contaminating the fuel.

• Take the cap off the fuel container carefully. Unscrew 

the cap on the fuel tank and fill it with the necessary 
quality, using a funnel.

• Take care not to spill any fuel.
• After filling the tank, screw the cap on tightly.
• During use, to prevent problems in starting the engine 

again, we strongly recommend that you avoid letting 
the fuel run out in the tank.

Fuel storage

• Gasoline is highly inflammable.
• Before going near any type of fuel, put out your 

cigarette, pipe or cigar.

• Store the fuel in a cool, well-ventilated place, in an 

approved fuel storage container.

• Never store the engine with fuel in the tank in a poorly 

ventilated place where the fumes produced by the 

CAUTION!

 Engine exhaust fumes are toxic. For 

this reason, you should not use the machine 
indoors.

CAUTION!

 Engine exhaust fumes can get very 

hot and may contain sparks. Do not use the 
machine near inflammable material.

CAUTION!

 It is very important to familiarize 

yourself with the release mechanism. In case of 
emergency you need to be able to release the 
machine quickly.

D. Fuel Mixture

CAUTION!

 

• Do not smoke while refueling!
• Open the cap on the tank by loosening it slowly.
• Fill the tank outdoor, far from flames or sparks.
• Never add fuel in the tank when the engine is 

running or hot to avoid the risk of fire (let the 
engine cool off before filling the tank).

• Avoid contact of the oil and fuel with the skin 

and eyes.

• Fill the tank in a well-ventilated place.
• Do not inhale the toxic fumes of the fuel 

mixture.

• Store the fuel mixture in suitable fuel containers 

only.

CAUTION!

 Do not use any other type of fuel than 

the type recommended in this manual. This 
machine is equipped with a two-stroke engine 
and should therefore be fueled with a mixture of 
unleaded gasoline (with a minimum octane rating 
= 90) and fully synthetic oil specific for two-speed 
engines that use unleaded gasoline in the 
proportions indicated in the table on the cover, fig. 
(

D

).

CAUTION!

 Control the specifications of the oil 

shown on the package; the use of oil lacking the 
specifications expressly indicated in this manual 
could cause serious damage to the engine!

CAUTION!

 The following precautions should be 

taken to reduce the fire hazard:
• Always ensure there is adequate ventilation.
• Do not smoke or take sources of heat or sparks 

near the fuel.

• Refuel with the engine off.
• Open the cap on the tank carefully to eliminate 

any excess pressure.

• Do not take the cap off the tank with the engine 

running.

• After fueling, close the cap tightly.

CAUTION!

 If you spill any fuel, wipe it off the 

machine. If you have spilt it on yourself, change 
your clothes at once. Avoid contact with the skin 
or eyes.

CAUTION!

 The muffler gets very hot during use 

and remains hot for some time after switching off 
the engine. This also applies at idle speed. Take 
every precaution to reduce the fire hazard, 
especially in the presence of inflammable 
materials or gas.

Содержание Premio B















Отзывы: