background image

 

Installation and use 

SOLID CONTROL MCK 2200 

12 

 
To enter programming (preferably with the machine stopped), press the "PROG" key 
ref. (H) for 3 SECONDS. 
The first constant 

to

 " Minimum detection time for solenoid valve opening " will appear; 

to change the value, simply press the two "+" and "-" keys ref.(M) and (L). 
To  switch  to  the  display  of  the  next  constant,  press  the  PROG  key  for  another  3 
SECONDS and so on until the last constant. 
After the constant 

to

 "Minimum detection time for solenoid valve opening", the following 

3 constants will appear in the following order: 

tC

 "Solenoid valve closure delay from 

the end of the plant detection", 

i

 "pulses/litre" of the flowmeter sensor, 

L

 "amount of 

product load" and 

Pr

 "calibration for pressure sensor". 

Once programming is complete, keep pressing the PROG key for 3 SECONDS and 
the new constants will be saved and you will return to the previous work configuration. 
To rapidly exit the programming phase, simply hold down the PROG key ref. (H) for 5 
SECONDS. 
 
 

4.7 

Totalisers full scale range 

4.7.1 

Working hours totaliser: 0 to 9999.9 (6-minute increments = 0.1 hours) can 
be reset by pressing the RESET key ref. (F) for 5 seconds upon start-up. 

4.7.2 

Partial plants totaliser: 0 to 99999 (increments of 1) can be reset by pressing 
the RESET key ref. (F) for 3 SECONDS while the number of partial plants is 
shown on the display (ref. O5). 

4.7.3 

Total plants totaliser: 0 to 99999 (increments of 1) cannot be reset. 

4.7.4 

Distributed  litres  totaliser:  0  to  99999  (increments  of  1)  can  be  reset  by 
pressing  the  RESET  key  ref.  (F)  for  3  SECONDS  while  the  number  of 
distributed litres is shown on the display (ref. O8). 

4.7.5 

Litres left totaliser: 0 to 99999 (decrements of 1) can be reloaded by pressing 
the  RESET  key  ref.  (F)  for  3  SECONDS  while  the  number  of  litres  left  is 
shown on the display (ref. O9). 

 

4.8 

Automatic mode  

In  automatic  mode,  the  opening  of  the  solenoid  valves  is  subject  to  the  two  lateral 
sonars. 
Just  as  an  example,  considering  just  the  right  section,  from  the  moment  the  sensor 
passes  in  front  of  the  plant  (switching  of  the  relative  input),  the  count  of  the  delay 
constant 

to

 " Minimum detection time for solenoid valve opening " relative to the sensor 

begins and the two "DCHO SONAR" segments light up on the display. 
If the count ends with a time greater or equal to the "to" delay, the solenoid valve is 
powered  and  allows  the  product  to  be  spread  on  the  plant  itself.  From  the  moment 
when the sensor no longer detects the plant (when the two "DCHO SONAR" segments 
switch  off  on  the  display),  the  count  of  the  other  delay  constant 

tC

  "Solenoid  valve 

closure delay from the end of the plant detection" begins. 

Содержание MCK 2200

















Отзывы: