Mazda B-Series Скачать руководство пользователя страница 30

Страница: 30 / 146

Mechanical WL-C

Engine

•

The cylinder head and the full floating cylinder head cover are made of aluminium alloy.

•

The steel laminated cylinder head gasket is available in three different thicknesses
depending on the piston protrusion. The gasket is marked respectively (refer to Engine
W/M).

•

The camshafts are supported in a separate bearing case, which is available as a
separate spare part.

•

For lubrication of the cam lobes, bearings / journals and rocker arms, the camshafts are
hollow and have oil bores at each lubricating point.

BT-50_01008

Exhaust camshaft

Oil passage

Intake camshaft

Location of cylinder no.1

Thrust force bearing boss

Hexagonal shaped surface

2 Oil

bore

NOTE:

The cylinder head surface must not be machined. If necessary, the cylinder head

must be replaced (refer to Engine W/M).

01-6 Service

Training

BT-50

Содержание B-Series



















































































































































Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды

Mazda B-Series, Руководство по обучению

Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды