Mazda B-Series Скачать руководство пользователя страница 45

Страница: 45 / 146

WL-C Engine

Intake-Air System

MAF Sensor

•

The MAF sensor with integrated IAT sensor no.2 is installed on the air filter.

MAF Learning Function

•

The MAF learning function is used to compensate any deterioration of the MAF sensor. It
should be carried out at each service interval by means of M-MDS (refer to chapter
‘Maintenance and Repair’).

MAF Data Reset

•

When the MAF sensor is replaced the adaptation values in the PCM must be reset by
means of M-MDS (refer to chapter ‘Maintenance and Repair’).

MAP Sensor / IAT Sensor No.1

•

The MAP sensor incorporates IAT sensor no.1 and is installed on the intake manifold.

BT-50_01052

1 Boost

sensor

3 PCM

IAT sensor no.1

Service Training BT-50

01-21

Содержание B-Series



















































































































































Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды

Mazda B-Series, Руководство по обучению

Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды