Mazda B-Series Скачать руководство пользователя страница 28

Страница: 28 / 146

Mechanical WL-C

Engine

Piston

•

In accordance with the adoption of the common rail injection system, the piston head
shape now incorporates the combustion chamber. Due to the modified piston shape the
compression ratio is reduced from 21.6: 1 on the WLT-3 engine to 18.0: 1.

•

A reduction of the internal friction and hence of the engine’s mechanical loss has been
achieved by coating of the piston skirt area.

NOTE:

The piston side marked with ‘F’ must be installed towards the timing gear-side of the

engine.

BT-50_01006

Combustion chamber

Piston skirt coating

Cooling oil channel

NOTE:

Oversize bearings for the crankshaft and connecting rods, as well as oversize

pistons are available in various dimensions (refer to Engine W/M).

01-4 Service

Training

BT-50

Содержание B-Series



















































































































































Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды

Mazda B-Series, Руководство по обучению

Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды