Mazda B-Series Скачать руководство пользователя страница 78

Страница: 78 / 146

Control System

WL-C Engine

Maintenance and Repair

MAF Sensor Learning Function

•

The MAF learning procedure by means of M-MDS must be carried out at every service
interval. During this procedure the MAF learning is performed at engine speeds of
750 min

-1

, 1850 min

-1

, and 2500 min

-1

. To perform the procedure select

Toolbox

Powertrain

Engine Checks

Learning

and follow the instructions.

•

The MAF learning procedure can also be initiated manually via DLC-1. Therefore,
connect terminal

TEN

(

est

gine) five times to ground within five seconds. The glow

indicator light is illuminated while MAF learning is performed and flashes five times after
the procedure is completed.

Replacing the MAF Sensor

•

After replacing the MAF sensor certain procedures have to be performed in the following
order:

1. Perform MAF sensor data reset procedure to reset the adaptation values in the PCM

for the MAF sensor. Therefore, select the option

Toolbox

Powertrain

Data

Reset

MAF sensor

and follow the instructions.

2. Perform KOEO self-test procedure.

3. Turn the engine switch to the OFF position.

4. Wait for 5 s.

5. Start the engine.

6. Perform KOER self-test procedure.

7. Turn the engine switch to the off position.

NOTE:

It is recommended to perform the MAF sensor learning function when a MAF data

reset has been carried out.

01-54 Service

Training

BT-50

Содержание B-Series



















































































































































Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды

Mazda B-Series, Руководство по обучению

Результаты поиска

Содержание B-Series

Отзывы:

Похожие инструкции для B-Series

Бренды по названию

Популярные бренды