Mazda 2013 CX-5 Скачать руководство пользователя страница 48

Страница: 48 / 223

DTC C0062:76 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2901000.html[1/7/13 9:29:40 AM]

Switch the ignition to off.

Using the M-MDS, perform the DTC

inspection for the SAS control module.

(See

DTC INSPECTION [STANDARD

DEPLOYMENT CONTROL SYSTEM]

(See

DTC INSPECTION [TWO-STEP

DEPLOYMENT CONTROL SYSTEM]

Are any DTCs detected?

(See

DTC TABLE [STANDARD

DEPLOYMENT CONTROL SYSTEM]

(See

DTC TABLE [TWO-STEP

DEPLOYMENT CONTROL SYSTEM]

No Go to the next step.

PERFORM DSC RELATED PARTS SENSOR

INITIALIZATION

Perform the DSC related parts sensor

initialization for the PCM using the M-MDS.

(See

DSC RELATED PARTS SENSOR

INITIALIZATION PROCEDURE

Is the DSC sensor initialization completed

normally?

YesGo to the next step.

No Replace the DSC HU/CM, then go to

the next step.

(See

DSC HU/CM

REMOVAL/INSTALLATION

VERIFY THAT THE SAME DTC IS NOT PRESENT

Clear the DTCs from the memory.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

Are the same DTCs present?

YesRepeat the inspection from Step 1.

If the malfunction recurs, replace the

DSC HU/CM, then go to the next

step.

(See

DSC HU/CM

REMOVAL/INSTALLATION

No Go to the next step.

VERIFY THAT NO OTHER DTCS ARE PRESENT

Are any other DTCs output?

YesGo to the applicable DTC inspection.

(See

ON-BOARD DIAGNOSIS [DYNAMIC

STABILITY CONTROL (DSC)]

No DTC troubleshooting completed.

< Previous

Next >

Back to Top

Содержание 2013 CX-5
































































































































































































































Результаты поиска

Содержание 2013 CX-5

Отзывы:

Похожие инструкции для 2013 CX-5

Бренды по названию

Популярные бренды

Mazda 2013 CX-5, Руководство по ремонту

Результаты поиска

Содержание 2013 CX-5

Отзывы:

Похожие инструкции для 2013 CX-5

Бренды по названию

Популярные бренды