Mazda 2013 CX-5 Скачать руководство пользователя страница 66

Страница: 66 / 223

DTC U0151:00 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2883700.html[1/7/13 9:30:21 AM]

Diagnostic procedure

STEP

INSPECTION

ACTION

INSPECT SAS CONTROL MODULE MALFUNCTION

Switch the ignition to off.

Using the M-MDS, perform the DTC inspection for the SAS control module.

(See

DTC INSPECTION [STANDARD DEPLOYMENT CONTROL SYSTEM]

(See

DTC INSPECTION [TWO-STEP DEPLOYMENT CONTROL SYSTEM]

Are any DTCs detected?

YesGo to applicable DTC inspection.

(See

DTC TABLE [STANDARD

DEPLOYMENT CONTROL SYSTEM]

(See

DTC TABLE [TWO-STEP

DEPLOYMENT CONTROL SYSTEM]

No Go to the next step.

INSPECT SAS CONTROL MODULE SIGNAL (CAN2 LINE) FOR OPEN CIRCUIT

Disconnect the DSC HU/CM connector.

Disconnect the SAS control module connectors.

Inspect for continuity between the following DSC HU/CM connector terminals

(vehicle harness-side) and SAS control module connector terminals (vehicle

harness-side):

DSC HU/CM terminal S—SAS control module terminal 3H

DSC HU/CM terminal P—SAS control module terminal 3I

Is there continuity?

YesGo to the next step.

No Repair or replace the wiring harness,

then go to Step 4.

INSPECT SAS CONTROL MODULE SIGNAL (CAN2 LINE) FOR SHORT CIRCUIT

Inspect for continuity between the following DSC HU/CM connector terminals

(vehicle harness-side) and body ground:

DSC HU/CM terminal S—body ground

DSC HU/CM terminal P—body ground

Is there continuity?

YesRepair or replace the wiring harness,

then go to the next step.

No Go to the next step.

Содержание 2013 CX-5
































































































































































































































Результаты поиска

Содержание 2013 CX-5

Отзывы:

Похожие инструкции для 2013 CX-5

Бренды по названию

Популярные бренды

Mazda 2013 CX-5, Руководство по ремонту

Результаты поиска

Содержание 2013 CX-5

Отзывы:

Похожие инструкции для 2013 CX-5

Бренды по названию

Популярные бренды