background image

7

Electrical Connection

Power Supply Cord

Electrical Connection Options

1.

 

Choose electrical connection type

Power supply cord 4-wire receptacle

(NEMA Type 14-30R): 

Go to steps 1-2 on 

page 9 for power supply cord strain relief: 

then steps 3-6 for 4-wire Power Supply 

Cord Connection section. Then, go to 

Venting Requirements.

3-wire direct connection: 

Go to steps 

1-2 on page 11 for direct wire strain relief: 

then steps 3-7 for 3-wire Direct Wire 

Connection section. Then go to Venting 

Requirements.

4-wire direct connection: 

Go to steps 

1-2 on page 10 for direct wire strain relief: 

then steps 3-8 for 4-wire Direct Wire 

Connection section. Then go to Venting 

Requirements. 

Power supply cord 3-wire receptacle

(NEMA Type 10-30R): 

Go to steps 1-2 on 

page 9 for power supply cord strain relief: 

then steps 3-5 for 3-wire Power Supply 

Cord Connection section.   

Then go to Venting Requirements.

NOTE:

 If local codes do not permit connection of a 

cabinet-ground conductor to neutral wire, go to “Optional 

3-wire Connection” section. This connection may be 

used with either a power supply cord or a direct wire 

connection.

Install Leveling Legs

Prepare dryer for leveling legs

1. 

To avoid damaging floor, use a large flat piece of cardboard 

from dryer carton; place under entire back edge of dryer. 

Firmly grasp dryer body (not console panel) and gently lay 

dryer down on cardboard.

Screw in leveling legs

2. 

Using a wrench and tape measure, screw legs into leg holes 

until bottom of foot is approximately 1/2" (13 mm) (to match 

height of 3.6 cu. ft. capacity washer) or 1½" (38 mm) (to 

match height of 3.8 cu. ft. capacity washer) from bottom of 

dryer.

Now stand the dryer on its legs. Slide the dryer until it is 

close to its final location. Leave enough room for electrical 

connection and to connect the exhaust vent.

Содержание WED4800BQ





















Отзывы: