background image

19

Troubleshooting

See the Use and Care Guide or visit our website and reference 

Frequently Asked Questions to possibly avoid the cost of a 

service call.

Close door and check that door strike aligns with door  

catch. If it is needed, slide door catch left or right within slot 

to adjust alignment.

Check door strike alignment

13.

Insert screws in hinge holes on 

dryer cabinet

12.

NOTE: 

Two people may be needed to reinstall door.

Insert screws into the bottom holes on left side of dryer 

cabinet. Tighten screws halfway. Position door so large  

end of door hinge slot is over screws. Slide door up so  

screws are in bottom of slots. Tighten screws. Insert and 

tighten top screws in hinges.

Use a small, flat-blade screwdriver to gently remove 4 hinge 

hole plugs on left side of dryer cabinet. Transfer plugs into 

hinge holes on opposite side of dryer cabinet.

Remove and transfer  

hinge hole plugs

11.

Remove door strike and door strike plug from dryer cabinet. 

Insert the door strike into door strike plug hole and secure 

with screw. Insert door strike plug into original door strike 

hole and secure with screw.

10. 

Remove door strike and  

 

door strike plug

Door strike plug

Door strike

Содержание WED4800BQ





















Отзывы: