background image

17

Reverse Door Swing (Optional)

29" 

Super Wide Side-Swing Door

Place towel on top of dryer to avoid damaging the surface.

NOTE: 

Magnetized screw driver is helpful.

Place towel on dryer

1.

Remove bottom screws

2.

Open dryer door. Remove bottom screws from dryer cabinet 

side of hinges. Loosen (do not remove) top screws from dryer 

cabinet side of hinges.

Lift door until top screws in dryer cabinet are in large part of 

hinge slot. Pull door forward off screws. Set door (handle side 

up) on top of dryer. Remove top screws from dryer cabinet.

Lift door off top screws

3.

Remove screws from hinges

4.

Remove screws attaching hinges to door.

Remove screws at top, bottom, and side of door (4 screws) 

that hold the inner and outer door together. Holding door over 

towel on dryer, grasp sides of outer door and lift to separate it 

from inner door. Set outer door aside.

NOTE: 

Do not pry apart with putty knife or screwdriver.  

Do not pull on door seal or plastic door catches.

Remove screws from door

5.

If you do not feel heat, turn off dryer, and check the 

following:

 

There may be 2 household fuses or circuit breakers for 

the dryer. Check that both fuses are intact and tight, or 

that both circuit breakers have not tripped. If there is still 

no heat, contact a qualified technician.

NOTE:

 You may notice an odor when the dryer is first heated. 

This odor is common when the heating element is first used.  

The odor will go away.

Содержание WED4800BQ





















Отзывы: