background image

DDDDDDD

DDDD

ww

w.maypole.ltd.uk

 

MAMMMMMMMMM

pole.ltd.uk

 

www.maypole.ltd.uk

 

 

 

RISK OF FIRE OR EXPLOSION

 

 

 

 

• 

Explosive gases may escape from the battery during the use of this product. This is normal, but please follow 
the following guidelines: 

• 

Do not use near flames or sparks 

 do not smoke in the area. 

• 

Ensure adequate ventilation during use. 

• 

Keep the area completely clear of combustible materials. 

• 

Never connect the smart jump cable output clamps together. 

• 

Do not allow battery to overheat. 

• 

Store in a dry area and take care to not expose to rain or moisture during use. 

• 

The jump starter is intended for use with 12V Lead-Acid, AGM & GEL batteries.  Do not use with non-
rechargeable batteries.  

 

WARNING 

 GENERAL SAFETY 

 

 

• 

Never connect to a battery suspected to be frozen. 

• 

This product should not be used for any purposes other than those listed 

 any other use will invalidate 

warranty. 

• 

Ensure that cables are regularly inspected and kept in good condition. 

• 

Do not store the device in locations 

that are likely to exceed 70˚C, for prolonged storage 15˚C is ideal.

 

• 

Never use the product if the device or its accessories are found to be worn or damaged. 

• 

This product contains no user-serviceable parts - never attempt to disassemble. 

• 

During operation, locate the unit as far away from the vehicle primary battery as the cables will permit. 

• 

This device contains a Lithium Ion battery. Do not allow battery to overheat. Do not crush, pierce or incinerate. 

• 

Position the unit such that it cannot inadvertatly become stepped on, tripped over or damaged. 

• 

Never place the device directly above the battery unto which it is connected; gases from the battery will 
corrode and damage the product. 

• 

Always follow battery 

manufacturer’s

 instructions for charging - electrical discharge from batteries can be 

dangerous 

• 

Battery electrolyte is acidic and likely to cause burns. The use of safety goggles and gloves when working with 
lead acid batteries is strongly advised. 

• 

Remove metal items such as rings, necklaces and watches while working with batteries. 

• 

This appliance is not for use by a person (including children) with reduced physical, sensory or medical 
capabilities or lack of experience or knowledge. 

 

PREPARATION OF THE BATTERY 

 

 

Refer to the vehicle manufacturer

’s

 handbook for battery maintenance, connection and charging guidelines.

 

 
 

3

 

1

 

2

 

Содержание MP7429








Отзывы: