Maxxus Multipress 9.1 Скачать руководство пользователя страница 9

Страница: 9 / 38

ENG

Assembly Step 3

Place the stand pipe with foot (29) on the rear side of the cross bar assembled in Step 1 and screw them togeth-

er using a M12x30 (37), two spring washers Ø12 (38) and two washers Ø12 (12).

Put the butterfly base frame (28) onto the pipe junction of the lower cross bar and the stand pipe (29) and screw

them together using three hexagonal head screws M10x90 (39), six washers Ø10 (9) and three safety nuts M10

(10).

Put both dumbbell plate brackets (34) in the mounts on the side of the weight slide (32) and fix each of them

with one headless screw M8x10 (24).

Slide both guide pipes (31) into the mounts on the weight slide (32).

Make sure that both dumbbell plate brackets on the weight slide are pointing upwards.

Slide a round rubber stop Ø60x42 (35) onto each of the guide pipes from below (31).

Then put the guide pipes (31) into the drill holes on the stand pipe (29) and fix each of them to the lower stand

pipe (29) from below with a hexagonal head screw M10x20 (36) and a washer Ø10 (9).

Now place the connecting tube (30) onto the guide pipe (31) from above. Fix the rear guide pipe (31) with a hex

agonal head screw M10x95 (41) and a washer Ø10 (9). Fix the rear guide pipe (31) with an Allen screw M10x20

(40) and a washer Ø10 (9).

Fix the connecting tube (30) using 3 hexagonal screws M10x90 (30), six washers and three safety nuts M10

(10) from above onto the cross frame and to the butterfly base frame (28).

Fix the connecting tube (30) at the side to the top cross frame using two hexagonal screws M12x30 (37), two

spring washers Ø12(38) and two washers Ø12 (12).

Assembly - Multipress

Содержание Multipress 9.1







































Результаты поиска

Содержание Multipress 9.1

Отзывы:

Maxxus Multipress 9.1, Руководство по установке, Страница: 9 / 38

Результаты поиска

Содержание Multipress 9.1

Отзывы: