Maxxus Multipress 9.1 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 38

background image

40

34

36

11

9

60

48

47

49

50

37

25

ENG

Assembly step 5

Insert the three cross tubes (37) - as shown in the picture - in the swivel bar or in the base. Slide one cover

(large opening) (48) with the open side out (see illustration) on each end of the tubes (37).

Then slide one round cushion (47) from each of the right and left of each of these three cross tubes (37) and

secure each with a cover (small opening) (49) and one hexagon bolt M8x25 (50).

Assembly step 6

Insert the shaft tube (34) into the upper opening of the standpipe and secure it with a locking pin (11). Mount the

pad of the armcurler (40) with two hexagon bolts M8x25 (60) and two Ø8 washers (32) on the shaft tube (34).

Secure the swivel tube of the armcurler (36) with the locking pin (11) at the front end of the swivel bracket.

Assembly - Training Bench

«
...
23
24
25
26
27
...
»

Содержание Multipress 9.1







































Отзывы:

Нет отзывов

Похожие инструкции для Multipress 9.1

Бренд: KaVo Страницы: 16

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

DVCPRO P2 Series

Бренд: Panasonic Страницы: 32

Бренд: Jawbone Страницы: 3

Бренд: AAON Страницы: 36

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды