Maxxus Multipress 9.1 Скачать руководство пользователя страница 15

Страница: 15 / 38

Traction Cable (61) - Length

10.215 mm

ENG

Assembly Step 7

Before you start with this step, remove the distance ball on one end of the traction cable (61). To do this loosen

the nut and remove the hexagonal head screw. Then loosen the U-bracket from the end of the cable. Now you

can remove the distance ball and the rounded holder.

Loosen the single roller (R1) out of the movable holder and the single roller (R2) out of the upper frame. Slide

the end of the traction cable (61) which you have just removed the distance ball from through the hole in the

movable holder. Feed the traction cable (61) through the upper frame pipe until it comes out of the opening

where the single roller (R2) had been. Fix the single rollers (R1) and (R2) back into their original positions

Now feed through the traction cable (61) under the single rollers (R3) and (R4) as shown in the diagram.

Then feed the traction cable (61) upwards and over the two rollers (DR1 & DR2) of the double roller with fixing.

From here feed through the traction cable (61) back down and under the single rollers (R5) and (R6).

Now loosen the single roller (R7) out of the top frame and the single roller (R8) out of the movable holder. Feed

the cable from below up through the opening where single roller (R7) was fixed and forwards through the frame.

The end of the traction cable must then be fed back through the opening in the movable holder. Fix roller (R7)

and (R8) back in their original positions.

At the end of this assembly step, replace the distance ball back onto the end of the traction cable (61).

Assembly - Multipress

Содержание Multipress 9.1







































Результаты поиска

Содержание Multipress 9.1

Отзывы:

Maxxus Multipress 9.1, Руководство по установке, Страница: 15 / 38

Результаты поиска

Содержание Multipress 9.1

Отзывы: