Maxxus Multipress 9.1 Скачать руководство пользователя страница 7

Страница: 7 / 38

ENG

Carefully unpack all delivered parts. Have someone there to help you as some of the training device parts are bulky and

heavy.

Check that all the parts and fixing materials (screws, nuts, etc.) have been delivered.

Assemble the parts carefully as any damages or defects occurring due to mistakes made at the time of assembly are

not

covered by the warranty or guarantee

. Therefore, read through the assembly instructions carefully before you start as-

sembling, follow each assembly step exactly as described and keep to the correct sequence of assembly as instructed.

Assembly of the training device must be carried out thoroughly by an adult person only.

Assemble the training device in a location which is level, clean and clear of obstructions. 2 people are required to carry out

the assembly.

Please be aware a possible risk of injury at the time of assembly and at each time of using this device exists. For this rea

son, always be careful and thorough in your actions when assembling this device.

Make sure that the parts necessary for each stage of assembly are only hand tightened together and only tighten parts

completely when all parts have been fitted together perfectly.

Training can only start when the training device has been fully assembled.

CAUTION: all necessary screws, nuts and washers required to assemble this training device are delivered pre-as-

sembled. Please loosen the fixing materials before each assembly step and follow the instructions as shown in the

drawings and descriptions and then tighten up the fixing materials again afterwards.

Assembly Step 1

Connect the front left side-frame (2) and the front right side-frame (3) to the pull-up cross bar (5). To do this, for each side

use; two hexagonal head screws M12x75 (11), four washers Ø12 (12), four safety nuts M12 (13) and a flat fixing plate (7).

Connect the left side-frame (2) and the right side-frame (3) at the bottom using the rear cross bar (1). Here you should use

two hexagonal screws M10x100 (8), four washers Ø10(9), four safety nuts M10 (10) and a bent fixing plate (8).

Fix the rear of the left side-frame (2) and the right side-frame (3) together at the top with the cross bar (4). To do this use

two hexagonal screws M10x100 (8), four washers Ø10 (9), four safety nuts M10 (10) and a bent fixing plate (8).

Note:

Please only tighten screws by hand until all component parts have been fitted together properly. Only after this should all

screws be tightened securely.

Assembly - Multipress

Содержание Multipress 9.1







































Результаты поиска

Содержание Multipress 9.1

Отзывы:

Похожие инструкции для Multipress 9.1

Бренды по названию

Популярные бренды

Maxxus Multipress 9.1, Руководство по установке

Результаты поиска

Содержание Multipress 9.1

Отзывы:

Похожие инструкции для Multipress 9.1

Бренды по названию

Популярные бренды