Maxxus Multipress 9.1 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 38

Maxxus Multipress 9.1 Скачать руководство пользователя страница 11

Traction Cable (55) – Length 2,515 mm

R1

R2

R3

R4

10

10

10

11

ENG

Assembly Step 5

Loosen and take out the three single rollers (R1, R2 & R4) from the frame.

Connect the end of the traction cable (55) to the mount on the weight slide.

Feed the traction cable (55) through the single roller (R1) and mount the single roller (R1) back onto the

T-frame.

Now feed the traction cable (55) through the single roller (R2) and single roller (R4). Then mount both rollers

(R2 & R4) back onto the frame.

Loosen the upper roller (R3) on the double roller (57). Pull the traction cable (55) down to form a loop large

enough below the single roller (R2) to fit the (R3) roller into. Then mount this back onto the top roller holder of

the double roller (57).

Then fix the end of the traction cable (55) to the double roller mount with fixing (56)

Assembly - Multipress

Double Roller, parallel (57)

Double Roller with fixing (56)

«
...
9
10
11
12
13
...
»

Содержание Multipress 9.1







































Отзывы:

Нет отзывов