background image

14 

 

3.0 

USING THE WINDLASS

 

 

 

3.1 

PERSONAL SAFETY WARNINGS

 

 

 



As  with  all  load  carrying  equipment,  the 
consequences  of  heavy  overload,  neglect  or 
misuse may be unexpected failure and exposure 
of  crew  and/or  vessel  to  risk.  Operate  the 
windlass with extreme care at all times.

 



Before  testing  the  windlass  for  the  first  time, 
check that all the wiring has been done correctly.

 



When  using  the  windlass  at  all  times  practice 
good  seamanship  and  adhere  to  the  following 
rules  in  order  to  avoid  any  likelihood  of  injury  or 
accident.

 



At  all  times  keep  hands,  feet,  loose  clothing, 
cordage and your hair WELL CLEAR.

 



Never  operate  the  windlass  from  a  remote 
station without maintaining a clear view of it and 
having  made  sure  that  everyone  is  well  clear  of 
the windlass, anchor and chain.

 



Never  use  the  windlass  under  power  with  the 
clutch  handle  inserted  into  clutch  nut  or 
emergency crank collar. 



When  engaging  the  pawl  while  chain  is  running, 
keep fingers away from the chain. Use clutch nut 
lever, underneath and guarded by the chainpipe. 



Always  motor  up  to  the  anchor  position  before 
retrieving  it  from  the  bottom.  Do  not  use  the 
windlass to pull the boat to the anchor.

 



If the anchor is fouled, do not use the windlass to 
break  it  out.  With  the  chain  stopper  taking  the 
load,  use  the  boat’s  engine  to  break  the  anchor 
loose.

 



When lowering the anchor under manual control, 
use  the  band  brake  or  friction  clutch  (if  fitted)  to 
control  the  speed  of  the  chain.  Never  lower  the 
anchor without maintaining safe chain speed



When  the  windlass  is  not  in  use, make  sure  the 
power  supply  is  isolated,  making  an  accidental 
operation thereby impossible.

 



Do  not  use  the  windlass  as  an  anchoring  point 
for  the  chain.  Engage  the  chain  stopper  when 
the windlass is not in operation.

 



Never  proceed  at  speed  without  first  ensuring 
that  the  chain  stopper  is  engaged.  Also  engage 
the  tensioner  to  keep  the  anchor  snug  in  the 
pocket.

 



When  using  the  windlass,  do  not  switch 
immediately  from  one  direction  of  rotation  to  the 
other, without waiting for windlass to stop. Abuse 
is not covered by warranty. 

 
 
 
 
 
 
 

 

  

 

 
 
 
 

 

Содержание VWC 4000 Series








































Отзывы: