Maxwell MW-3010, Инструкция по эксплуатации

Страница: 10 / 32

10
ENGLISH
•
If you cannot define the fabric structure, find a spot
that is inconspicuous when the item is being worn
and select the ironing temperature experimentally
(always start with the lowest temperature and raise
it gradually until you get the desired result).
•
Corduroy and other fabrics that become glossy
quickly should be ironed strictly in one direction
(in the direction of the pile) with slight pressure.
•
To avoid appearance of glossy spots on synthetic
and silk fabrics, iron them backside.
SETTING THE IRONING TEMPERATURE
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Turn the control knob (11) to set the required ironing
temperature: «•», «••», «•••» or «MAX», depend-
ing on the type of fabric, the indicator (7) will light up.
• Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go out
and you can start ironing.
Note:
– If you are ironing at high temperature but you need
to switch to lower temperature, wait until the sole-
plate temperature decreases and the indicator (7)
lights up, and only then you may start ironing.
WATER SPRAY
•
You can dampen the fabric by pressing the water
spray button (5) several times.
•
Make sure that there is enough water in the water
tank (10).
DRY IRONING
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Set the continuous steam supply knob (3) to the
position
– the steam supply is off.
• Turn the control knob (11) to set the required iron-
ing temperature: «•», «••», «•••» or «MAX»,
depending on the type of fabric, the indicator (7)
will light up.
•
Once the temperature of the soleplate (13)
reaches the set point, the indicator (7) will go out
and you can start ironing.
•
After you finish ironing, set the temperature con-
trol knob (11) to the “MIN” position.
•
Pull the power plug out of the mains socket and let
the iron cool down completely.
STEAM IRONING
While steam ironing it is necessary to set the ironing
temperature «•••», «МАХ».
•
Place the iron on its base (9).
•
Set the continuous steam supply knob (3) to the
position
– the steam supply is off.
•
Insert the power plug into the mains socket.
•
Make sure that there is enough water in the water
tank (10).
•
Turn the control knob (11) to set the required iron-
ing temperature: «•••» or «MAX», the pilot lamp
(7) will light up.
•
When the soleplate (13) reaches the set temperature,
the indicator (7) will go out, you can start ironing.
•
Turn the continuous steam supply knob (3) to the
position
– steam supply is on, steam will start
going out from the soleplate (13) openings.
•
After you finish ironing, set the temperature con-
trol knob (11) to the position «MIN», and the con-
tinuous steam supply knob (3) to the position
– steam supply is off.
•
Pull the power plug out of the mains socket and let
the iron cool down completely.
ATTENTION!
If the steam is not constantly supplied during opera-
tion, check whether the temperature control knob (11)
is set properly and there is water in the water tank (10).
BURST OF STEAM
The burst of steam function is useful for ironing folds
and can only be used at high ironing temperatures
(when the temperature control knob (11) is set to the
position «•••», «МАХ»).
•
When pressing the burst of steam button (4) steam
will go out of the iron soleplate more intensively.
Note:
To avoid water leakage from the steam openings,
press the burst of steam button (4) with an interval no
less than 4-5 sec.
VERTICAL STEAM
Vertical steam function can be used only at high iron-
ing temperatures (that is, when the temperature con-
trol knob (11) is set to «•••» or «MAX»). Hold the iron
vertically at the distance of 10-30 cm from the clothes
and press the burst of steam button (4) with an inter-
val no less than 4-5 sec., steam will be released from
the openings of the iron soleplate (13) intensively.
IMPORTANT INFORMATION: Vertical steaming is
not recommended for synthetic fabrics.
•
To avoid fabric melting, do not touch it with the
iron soleplate while steaming.
•
Never steam clothes on a person as temperature
of the released steam is very high, use a clothes
hanger or a coat rack.
•
After you finish ironing, switch the iron off, wait
until it cools down completely, then open the water
inlet lid (2), turn over the iron and pour out the
remaining water.
STEAM CHAMBER CLEANING
To prolong lifetime of the iron we recommend clean-
ing the steam chamber regularly.
•
Set the continuous steam supply knob (3) to the
position
.
•
Fill the water tank (10) up to the maximal mark
«MAX».