background image

Visit: www.seekerwireless.co.uk for potential software updates

Caravans
Power can be taken directly from the leisure battery on the caravan. The ignition cable should be connected to 
the ignition key circuit which can be traced using the charts below. The caravan will either be fitted with the 
13 Pin Euro Connector or have two 7/8 Pin connectors. 

                                        

Caution:

 All electrical work should be carried out by a competent person. 

If in doubt seek advice from a qualified electrician.
 

Electrical installation:

Whilst the adhesive is curing prepare the electrical connections for the Control Box. The Control Box 
requires a permanent 12V supply and a secondary 12V supply that provides power when the engine of the 
vehicle is running. Note: the brake light circuit is not suitable. 

It is recommended to create a new circuit direct to the battery using a minimum cable cross sectional area 
of 2.5mm2 and an inline fuse of 5A. Do not connect to existing circuits that supply high power devices such 
as water pumps, air conditioning units or sources of interference such as electric igniters for gas stoves. 
Route cables carefully avoiding areas of excessive heat such exhaust systems and any moving parts in the 
engine compartment or drive shafts.

 

 

Power Cable colours:

 

 

Black  

Negative Earth

 

 

Green  

Ignition (+12V) 

  Red 

 

+12V

Join Power Cable to new circuit using a 
robust connection method such as...
• Crimp connectors
• Screw terminal connector block
• Snap fit automotive tap connectors

   

   

   

   

13 Pin Euro Connector

1
2
3
4
5
6
7
8
9
10
11
12
13

12S 7 Pin Connector

1
2
3
4
5
6
7

Left 

Hand 

Indicator 

    

Rear fog light(s) 

 

 

 

Earth for contacts 1 to 8 

 

 

 

Right 

Hand 

Indicator 

    

Right Hand Side lights, marker lights & number plate light.
Brake 

lights    

Left Hand Side lights, marker lights & number plate light.
Reversing 

light(s) 

    

Positive direct from battery (Power) 

 

 

Positive ignition key on (Fridge)   

 

 

Earth return for contact 10 

 

 

 

Signalling connection to trailer   

 

 

Earth return for contact 9 

 

 

Reversing 

light(s) 

    

Positive ignition key on (Battery Charging)   

 

Earth 

 

     

Positive direct from battery (Power) 

 

Reverse Sensor (Optional) 

 

 

 

Positive ignition key on (Fridge)   

 

 

Earth return for contact 6   

 

 

Yellow
Blue
White
Green
Brown
Red
Black
Pink
Orange
Grey
White/Black
White/Blue
White/Red

Yellow
Blue
White
Green
Brown
Red
Black

Page 8

Terminal No.

Function

13 core wire colour

Содержание MXL003/65





















Отзывы: