Maxon TUK-A-WAY 80-3LM Скачать руководство пользователя страница 31

Страница: 31 / 36

11921

Slauson

Ave.

Santa

Springs,

CA.

90670

(800)

227-41

(888)

771-7713

PAGE 31

HOOK INSTALLATION

HOOK ASSEMBLY

P/N 227700

WELD PAD EYE FIRST

P/N 226938

Weld the Pad

Eye to the Unit in the

up position, insert the

Hook through the Pad

Eye. Weld the Chain to

the inside wall of the

Extension Plate Tube,

leaving only enough

slack to enable the

Hook to be removed

and reattached.

ADD SHIM

PLATE

264731

4-7/16

PLATFORM ADJUSTMENT

If Platform tip does not touch the ground, remove shackle plate from both sides. Weld shim

plate (P/N 264731) in between flats. Check platform adjustment. Add an addition 1/16 or 1/

8 shim if required.

REMOVE ORIGINAL

SHACKLE PLATE

THESE SURFACES

TO BE FLUSH

SHIM

264732 (1/16)

201999 (1/8)

Содержание TUK-A-WAY 80-3LM





































Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды

Maxon TUK-A-WAY 80-3LM, Руководство по установке

Результаты поиска

Содержание TUK-A-WAY 80-3LM

Отзывы:

Похожие инструкции для TUK-A-WAY 80-3LM

Бренды по названию

Популярные бренды