Maxon MXT-25 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 61

background image

1

1921 Slauson

A

ve. Santa Fe Springs, CA. 90670 (800) 227-41

16 F

AX (888) 771-7713

11

PERIODIC MAINTENANCE CHECKS

Never operate the Liftgate if parts are loose or missing.

WARNING

NOTE:

Make sure vehicle is parked on level ground while performing the

maintenance checks.

Quarterly or 1250 Cycles (whichever occurs fi rst)

Semi-annually or 2500 Cycles (whichever occurs fi rst)

Visually check the platform hinge pins for excessive wear and broken welds. See

PARTS

BREAKDOWN

section for replacement parts. Also, do the

Quarterly or 1250 Cycles

maintenance checks.

Check the hydraulic

fl

uid level in the pump reservoir. Refer to the

CHECKING HYDRAULIC

FLUID

procedure in the

PERIODIC MAINTENANCE

section.

If hydraulic

fl

uid appears contaminated, refer to the

CHANGING HYDRAULIC FLUID

procedure in the

PERIODIC MAINTENANCE

section.

Keep track of the grade of hydraulic

fl

uid in the pump reservoir and never mix two different

grades of

fl

uid.

Check all hoses and

fi

ttings for cha

fi

ng and

fl

uid leaks. Tighten loose

fi

ttings or replace

parts as required.

Check electrical wiring for cha

fi

ng and make sure wiring connections are tight and free of

corrosion. Use dielectric grease to protect electrical connections.

Check that all

WARNING and instruction decals

are in place. Also, make sure decals are

legible, clean and undamaged.

Check that all bolts, nuts, and roll pins are in place. Make sure roll pins protrude evenly
from both sides of hinge pin collar. Replace fasteners and roll pins if necessary.

PERIODIC MAINTENANCE

!

Check for rust and oily surfaces on Liftgate. If there is rust or oil on Liftgate, clean it off.
Touch up the paint where bare metal is showing. MAXON recommends using aluminum
primer touchup paint.

Damaged cylinder seals and contaminated hydraulic fl uid can result from paint-
ing the polished portion of the cylinder rod. To prevent damage, protect the
exposed polished portion of the cylinder rod while painting.

CAUTION

Pump EP chassis grease in each lube

fi

tting on the cylinders and arms until grease

starts oozing from ends of the bearings. The lubrication diagram on the

PERIODIC

MAINTENANCE CHECKLIST SHEET

shows where to

fi

nd the lube

fi

ttings. Wipe off

excess grease with a clean lint-free cloth.

«
...
9
10
11
12
13
...
»

Содержание MXT-25






























































Отзывы:

Нет отзывов

Похожие инструкции для MXT-25

Бренд: Lampert Страницы: 18

Бренд: VENCO Страницы: 4

MODULEX EXT Series

Бренд: Unical Страницы: 52

Бренд: Perma Страницы: 26

Бренд: Lampert Страницы: 24

Бренд: Kenco Страницы: 15

Бренд: ATH Страницы: 76

Бренд: Kühtreiber Страницы: 44

Бренд: ESAB Страницы: 45

Бренд: SPINOGY Страницы: 27

Бренд: Pro-Lift Страницы: 20

Бренд: FM Страницы: 16

Бренд: F.F. Group Страницы: 82

Бренд: WALTCO Страницы: 44

Бренд: morse Страницы: 4

Бренд: morse Страницы: 6

Бренд: morse Страницы: 7

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды