31
matrix 1
ON/OFF
Switch
7-Day
Timer
LIMIT
SWITCH
ON-LINE
24V
GND
UL ALARM 12V
ALARM RET
RESET
GND
GATE
TAMPER
MAG
LOCK
OPEN
RIGHT
OPEN
LEFT
MAGLOCK
DELAY
PRIMARY
GATE
SAFETY
CENTER
EXIT
OPEN
MAX
GATE SPEED
STOP
CLOSE
ANTI
TAILGATE
CLOSE TIMER
POSITION
RECORDER
ID
PLUG
AUTOMATIC OPEN/CLOSE CONTROLS
BATTERY
BACK-UP MODE
MATRIX 1
PHOTOCELL
EDGE 1
EDGE 2
ID PLUG
ERROR
OPEN
COM
CLOSE
Tamper NO
COM
GND
Tamper IN
OFF
OFF
ON
EXIT
PARTIAL
OPEN
OBD PORT
MOTOR MOTION
CENTER
REVERSE SENSITIVITY
MOTOR OVERLOAD
NO LIMIT SWITCH /
CLAMP SLIPPING
MIN
MAX
12VDC
GND
24VDC
GND
MAX
MIN
OFF
SAFETY
LEAVE
OPEN
LEAVE
CLOSED
MADE in USA
OPEN
1 TIME
2Sec
1.5Sec
COM
NC
BATTERY
IN USE
POWER
GATE
STATUS
(+)
UL
ENTRAP
PHOTOCELL
GND
STRIKE
GND
KEYP
AD / RDR
GND
FIRE DEPT
GND
MAX OPEN
GND
RADIO SIG.
RADIO GND
OPEN
STOP
CLOSE
COM
GA
TE DISABLE
PEN
STOP
ER
EXIT
CENTER
REVERSE SENSITIV
OTOR OVERLOAD
WITCH /
PING
MAX
IN
OFF
ST
12VDC
GND
ELL
DR
gate disable
GND
GA
TE DISABLE
ON
OFF
IMPORTANT:
Limit switches
MUST
be
learned
BEFORE
Partial Open can be recorded.
To
RECORD
PARTIAL OPEN:
1.
With gate in
CLOSED position
, press and release
PARTIAL OPEN
button to START recording. Blue LED starts flashing.
2.
Press 3-button station
OPEN
button to start gate’s open cycle.
3.
Press 3-button station
STOP
button when gate is in desired partial open position (Beyond center loop).
4.
Press
PARTIAL OPEN
button AGAIN to STOP recording. Blue LED stops flashing,
open position has been recorded. LED remains
ON
.
To
ERASE
PARTIAL OPEN recording
:
Press and
HOLD
PARTIAL OPEN
button for 5 sec. LED turns
OFF
.
partial open
24V
GND
UL ALARM 12V
ALARM RET
RESET
GND
GATE
TAMPER
MAG
LOCK
OPEN
RIGHT
OPEN
LEFT
MAGLOCK
DELAY
PRIMARY
GATE
SAFETY
CENTER
EXIT
OPEN
MAX
GATE SPEED
STOP
CLOSE
ANTI
TAILGATE
CLOSE TIMER
POSITION
RECORDER
ID
PLUG
AUTOMATIC OPEN/CLOSE CONTROLS
BATTERY
BACK-UP MODE
MATRIX 1
PHOTOCELL
EDGE 1
EDGE 2
ID PLUG
ERROR
OPEN
COM
CLOSE
Tamper NO
COM
GND
Tamper IN
OFF
OFF
ON
EXIT
PARTIAL
OPEN
OBD PORT
BLACK BOX
MOTOR MOTION
CENTER
REVERSE SENSITIVITY
MOTOR OVERLOAD
NO LIMIT SWITCH /
CLAMP SLIPPING
MAX
12VDC
GND
24VDC
GND
MIN
OFF
SAFETY
LEAVE
OPEN
LEAVE
CLOSED
MADE in USA
OPEN
1 TIME
2Sec
1.5Sec
COM
NC
BATTERY
IN USE
POWER
GATE
STATUS
MOTOR
ON-LINE
LIMIT
SWITCH
ON-LINE
(+)
GND
(-)
PRIMARY
GATE
(+)
GND
(-)
SEC
GATE
UL
ENTRAP
PHOTOCELL
GND
STRIKE
GND
KEYP
AD / RDR
GND
GND
MAX OPEN
GND
RADIO SIG.
RADIO GND
OPEN
STOP
CLOSE
COM
GA
TE DISABLE
OPEN
CLAMP SLIP
24VDC
GND
SIG.
ND
OPEN
STOP
CLOSE
POSITION
RECORDER
PARTIAL
OPEN
MOTOR MOTION
CAUTION:
Gates partial
OPEN
position
MUST
be outside the
Center Loop when in-ground
loops have been installed.
CENTER LOOP
NOTE:
The
FIRE DEPT
and/or
MAX
OPEN
connected devices will always
FULLY
open gates even when the
partial open is being used.
An ON/OFF switch or 7-Day timer devices can be connected to the
GATE DISABLE
input. When these devices are turned ON, they will
DISABLE
normal opening
devices such as keypad, exit loop etc. The
FIRE DEPT
/
MAX OPEN
and
RADIO
inputs will remain enabled when
GATE DISABLE
has been turned ON. This is
useful when the gated area needs to be secured from ALL but emergency or
authorized vehicle entry. Some examples are: Residential home vacation period or
during closed hours of a business when no one can monitor the property.
When GATE DISABLE is turned ON:
The operator will beep for
3 minutes
BEFORE arming itself.
This allows time to turn ON
GATE DISABLE
and
leave the property before it is armed.
When FIRE DEPT/MAX OPEN gets activated:
Gate opens and
GATE TAMPER
relay will activate immediately.
When RADIO Input gets activated:
Gate opens and
GATE TAMPER
relay will activate
after 3 min
. This allows time to turn OFF
GATE DISABLE
or disarm an existing building alarm system if connected.
IMPORTANT:
It is
NOT
recommended activating the
GATE DISABLE device
while persons are present inside the property.
Enabled inputs when
GATE DISABLE
is turned
ON
.
A gate can set to partially open by recording the
PARTIAL OPEN
gate cycle. LED will stay lit
when
PARTIAL OPEN
is ON.
NOTE:
See page 44 for
more information about
this unique feature.
