background image

Page 9 of 13 pages

 

50.

 

Using the supplied bolts and nuts, attach the presecured metal ends of the 

REAR

 struts (each is approx. 13 

1/2 

inches long) to the BOTTOM side of 

the fuselage-mounted strut bracket on each side of the fuselage. 

 

If you will 

not

 fold the wings, „snug‟ each nut onto its bolt. 

 

If your Storch 

will

 have folding wings, leave these bolts and nuts barely 

finger-tight, then apply a dab of hot-melt glue to secure the nuts onto 
their bolts. 

51.

 

Slide a supplied 3-inch long metal tube onto each of the free ends of the 
four composite struts. 

 

If you will 

not

 fold the wings: Use the predrilled holes in the metal tubes and supplied screws to attach the outer end of  

each front strut to the „center‟ of the three predrilled holes as shown below. 
 
 
 
 
 
 
 
 
 
 
 
 
 

Front strut attached to bottom of the wing from bolt in composite strut bracket.   Back strut attached to bottom of the wing.

 

 

If you will 

not

 fold the wings: Apply CA to secure the screws and their struts to the wing and each strut within its metal tube. 

 

If your Storch 

will

 have folding 

wings: Apply a dab of petroleum 
jelly to the metal end of each strut 
where it touches the wing to act 
as a lubricant and protection from 
glue; then, apply a small amount 
of thin CA adhesive to harden the 
predrilled holes in the wing, and 
use the metal tubes and supplied 
screws to attach the outer end of 
each strut to the predrilled hole 
in the wing as shown above, but 

leave these screws loosely finger-tight

52.

 

Apply a small „dot‟ of hot-melt glue to secure and „vibration-proof‟ … 

a.

 

The heads of the hinge bolts at the top of each wing panel and the exposed threads 
below the hinge-bolt‟s nut at the lower surface of each wing panel. 

b.

 

The head of each bolt, nut 
and screw associated with 
each of the four wing 
struts, and the exposed 
threads below the four strut 
bracket bolts (as shown in 
the two photos to the right 
on this page). 

53.

 

Use a „dot‟ of hot-melt glue to attach the 
diagonal braces at each side of the 
vertical and above the horizontal 
stabilizer. 
 
 
 
 
 
 

N

N

e

e

w

w

 

 

c

c

o

o

m

m

p

p

o

o

s

s

i

i

t

t

e

e

 

 

 

 

s

s

t

t

r

r

u

u

t

t

 

 

b

b

r

r

a

a

c

c

k

k

e

e

t

t

 

 

V.2-150423 

Entire Contents © Copyright 2013 by Maxford USA

 

Nose 

Содержание Fieseler Fi-156c STORCH














Отзывы: