background image

i-32V5 

Air/water inverter heat pumps with axial fansi

7

3. PERMITTED USE

• 

The company excludes any contractual and extra contractual liability for damage caused to persons, animals or objects, by incorrect instal-

lation, setting and maintenance, improper use of the equipment, and the partial or superficial reading of the information contained in this 

manual.

• 

These units are built for the heating and/or cooling of water. Any other use not expressly authorised by the manufacturer is considered 

improper and therefore not allowed. The fluid to be used is exclusively water or a mixture of water and glycol in case of low water tem-

peratures.

It is absolutely NOT permitted to connect the flow of heated water from the machine directly to the taps of the sanitary 

circuit. This fluid is not intended for sanitary use and must not be ingested.

• 

The installation place and the water and electric circuit must be established by the plant designer and must take into account both technical 

requirements as well as any applicable local laws and specific authorisations.

• 

All work must be carried out by experienced and qualified personnel, competent on the existing regulations in country where the installa-

tion takes place.

• 

This appliance is intended to be used by expert or trained operators in shops, light industry and in factories, or for commercial use by 

non-expert personnel.

• 

The appliance may be used by children at least 8 years old and by persons with reduced physical, sensory or mental capabilities or without 

experience or the necessary knowledge as long as they are supervised or after they themselves have received instructions on the safe use 

of the appliance and understand the relevant dangers. Children must not play with the appliance. The cleaning and maintenance which the 

user is expected to carry out on the unit cannot be done by children without supervision.

• 

Direct interaction with the unit by persons with electrically controlled medical devices, such as pacemakers, is prohibited, as harmful inter-

ference may result. It is recommended that an adequate distance be maintained from the installation site of the unit, as indicated by the 

medical system used.

Persons with electrically controlled medical device should exercise caution when interacting with the unit.

4. GENERAL SAFETY REGULATIONS

Before starting any type of operation on the units, every operator must be perfectly familiar with the operation of the machine and its controls 

must have read and understood all the information in this manual.

It is strictly forbidden to remove and/or to tamper with any safety device.

Children or unassisted disabled persons are not allowed to use the appliance.

Do not touch the appliance when barefoot or parts of the body are wet or damp.

It is forbidden to perform any cleaning operation when the master switch is ‘ON’.

It is forbidden to pull, detach or twist the appliance’s electric cables, even if it is disconnected from the power supply.

Do not step on, sit down on and/or place any type of object on the appliance.

Do not spray or pour water directly on the unit.

Do not dispose of, abandon or leave within reach of children packaging materials (cardboard, staples, plastic bags, etc.) as 

they may represent a hazard.

Any routine or extraordinary maintenance operation must be carried out with the machine stopped and disconnected.

Do not place your hands or introduce screwdrivers, spanners or any other tools on moving parts.

The machine operator and maintenance personnel must receive suitable training for the performance of their tasks in safety.

Operators must know how to use personal protective equipment and the accident-prevention rules of national and interna

-

tional laws and regulations.

Содержание i-32V504

















































Отзывы: