Max HVR41G4 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 17

Max HVR41G4 Скачать руководство пользователя страница 5

5

3.

DO NOT OPERATE THE TOOL NEAR A FLAMMABLE
SUBSTANCE

Never operate the tool near a flammable substance (e.g.,
thinner, gasoline, etc.). Volatile fumes from these substanc-
es could be drawn into the compressor and compressed to-
gether with the air and this could result in an explosion.

4.

NEVER USE THE TOOL IN AN EXPLOSIVE ATMOS-
PHERE

Sparks from the tool may ignite atmospheric gases, dust or
other combustible materials.

5.

DO NOT USE A WRONG FITTINGS

The connector on the tool must not hold pressure when air
supply is disconnected. If a wrong fitting is used, the tool
can remain charged with air after disconnecting and thus
will be able to drive a fastener even after the air line is dis-
connected, possibly causing injury.

6.

DISCONNECT THE AIR SUPPLY AND EMPTY THE
MAGAZINE WHEN THE TOOL IS NOT IN USE

Always disconnect the air supply from the tool and empty
the magazine when operation has been completed or sus-
pended, when unattended, moving to a different work area,
adjusting, disassembling, or repairing the tool, and when
clearing a jammed fastener.

7.

INSPECT SCREW TIGHTNESS

Loose or improperly installed screws or bolts cause acci-
dents and tool damage when the tool is put into operation.
Inspect to confirm that all screws and bolts are tight and
properly installed prior to operating the tool.

8.

DO NOT TOUCH THE TRIGGER UNLESS YOU INTEND
TO DRIVE A FASTENER

Whenever the air supply is connected to the tool, never
touch the trigger unless you intend to drive a fastener into
the work. It is dangerous to walk around carrying the tool
with the trigger pulled, and this and similar actions should
be avoided.

9.

NEVER POINT THE DISCHARGE OUTLET TOWARD
YOURSELF AND OTHER PERSONNEL

If the discharge outlet is pointed toward people, serious ac-
cidents may be caused when misfiring. Be sure the dis-
charge outlet is not pointed toward people when connecting
and disconnecting the hose, loading and unloading the fas-
teners or similar operations.

10. USE SPECIFIED FASTENERS (SEE PAGE 7)

The use of fasteners other than specified fasteners will
cause the tool malfunction. Be sure to use only specified
fasteners when operating the tool.

11. PLACE THE DISCHARGE OUTLET ON THE WORK SUR-

FACE PROPERLY

Failure to place the discharge outlet of the nose in a proper
manner can result in a fastener flying up and is extremely
dangerous.

12. DO NOT DRIVE FASTENERS CLOSE TO THE EDGE

AND CORNER OF THE WORK AND THIN MATERIAL

The workpiece is likely to split and the fastener could fly free
and hit someone.

Thinner

Gasoline

«
...
3
4
5
6
7
...
»

Содержание HVR41G4


















Отзывы:

Нет отзывов