Max HVR41G4 Скачать руководство пользователя страница 16

16

9

Fit a Cylinder Cap Seal onto the upper part of the body.

0

Place the Cylinder Cap onto the Cylinder Cap Seal.

a

Holding down the Cylinder Cap, tighten the four Screws 
(M5×20) with the 4 mm hex. wrench.

Make sure that the Cylinder Cap has been secure-
ly and uniformly clamped to the body with the 
four Screws (M5×20) at the specified tightening 
torque.

NOTICE:

Tighten the Screws evenly in the diagonal lines. Specified 
tightening torque should be equal 100 to 120 kgf-cm (86.8 to 
104.2 in lbs.).

8. MAINTAIN FOR PERFORMANCE

1

DO NOT FIRE THE NAILER WHEN IT IS EMPTY

2

USE RECOMMENDED OIL

The velocite or turbine oil should be used to lubricate the tool. 
Upon completion of operations, place 10 drops of oil into the air 
plug inlet with the jet oiler. (Recommended Oil : ISO VG32)

3

INSPECT AND MAINTAIN DAILY OR BEFORE OPERA-
TION

Disconnect air supply and empty the magazine when inspect-
ing or maintaining the tool.

(1)

Drain air compressor

(2)

Tighten all screws

(3)

Keep contact arm moving smoothly

9. STORING

1

When not in use for an extended period, apply a thin coat of 
the lubricant to the steel parts to avoid rust.

2

Do not store the tool in a cold weather environment. Keep 
the tool in a warm area.

3

When not in use, the tool should be stored in a warm and 
dry place. Keep out of reach of children.

4

All quality tools will eventually require servicing or replace-
ment of parts because of wear from the normal

10. TROUBLE SHOOTING/REPAIRS

The troubleshooting and/or repairs shall be carried out only 
by the MAX CO., LTD.authorised distributors or by other 
specialists.

Supplement to the operating instruction

According to the European Norm EN 792-13 the regulation is val-
id from 01.01.2001 that all fastener driving tools with contact ac-
tuation must be marked with the symbol "Do not use on 
scaffoldings, ladders" and they shall not be used for specific ap-
plication for example:

when changing one driving location to another involves the 
use of scaffoldings, stairs, ladders or ladder alike construc-
tions e.g. roof laths,

closing boxes or crates,

fitting transportation safety systems e.g. on vehicles and wag-
ons.

4mm hex. wrench

Screw M5×20 (4 pcs.)

Cylinder Cap

Third

Example of Fastening

Order of Screws

Second

First

Fourth

WARNING

WARNING

Содержание HVR41G4


















Отзывы: