background image

KK-642.014 Rev.No:1  01.08.12                                                                                                                                                             Page | 8  

  

9- POWERING THE PANEL 

 

9.1 Normal 

During normal mode, only green system is on LED lights. On the screen the gas levels read by channels is 

 

9.2 Alarm 

When  the  gas  detectors  exceed  the  levels  of  predetermined  threshold  levels  in  each  channel,  panel  goes 
into alarm mode. These alarms can be either low or high alarm level. In these situations each assigned output 
is activated. Pressing Reset makes the system work in initial position. 

 

9.3 Fault 

In case of  any fault condition at  the panel leads to  light 

“General Fault” LED, rings the buzzer ad fault relay 

changes  its  switch. When fault  condition disappears,  panel  automatically turns  back  to  its  normal  operating 
status. 

 

10- PANEL MENUS 

 

In normal mode, access level of the panel is 1. In order to see the panel configuration and reach the functions 
of  access  level  2,  first  you  need  to  main menu. To  do  this,  in  normal operating mode press 

“Enter”  button. 

Under the main menu there are  2  submenus. These  are 

“Visualization” and “Access level 2” menus. These 

menus are selected by using 

“Up (+)” and “Down (-)” buttons. Then, pressing “Enter” button results to enter the 

selected submenu.

 

 

10.1 Visualization 

When Visualization function is selected, pressing 

“Enter” button pops up 4 sub visualization function. 

To enter these sub-functions, function is  selected by using 

“Up (+)” and “Down (-)” buttons. Then, pressing 

“Enter” button results to enter the selected sub-function.

 

 

 

*** Visualize ***

 

Relays status 
Sounders status 
Signal levels 
Configuration 

----------------------------------------------------------------- 

Enter 

– Ok 

Exit 

–Up 

Menu 

Содержание MG-400





















Отзывы: