Matsusada 35 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 73

background image

１

Introduction

1

１

Introduction

１－１

Introduction

Thank you very much for your purchase of our product.
We have done our best for our quality control of out products. Please handle this unit
properly according to this instruction manual so that you can use the full capacity of
this unit and operate it safely and smoothly in high efficiency for long.
If you find any doubtful or unknown point or omission in this instruction manual, please
kindly contact us immediately.

１－２

Unpacking the unit

When unpacking the unit, please check the following accessories are enclosed with the

unit main body.

Accessories

・

Instruction manual

・

USB diver Install guide (for LUs1 option)

・

USB driver disc (for LUs1 option)

・

CO-M Cable (option nothing)

・

CO-Optical fiber cable (for LGob option)

１－３

Environmental requirements

Warning



Install the unit horizontally when use.



Never place any object on the power supply.



Use the power supply where the ventilation condition is good.



Do not operate the power supply in a dusty area or in corrosive gas environment.

１－４

Notes

Warning



When system has high voltage power supply, equipments connected might receive

damage due to high voltage.



When operate with GPIB interface, connect only cables required for system operation.



The power supply has protection for intermittent short circuit, however operation with

repeatable short circuit with arc should be avoided.



The power supply has enough protection for noise, however if hung-up or voltage

output, which is not programmed, are observed, turn of the power supply and reset
the but, then resend the command again from controller.



Any system change shall be done while the power of all the equipments of system is

turned off. Sometimes it prevents the unit to function properly that causing of high
voltage.

！



！



«
...
5
6
7
8
9
...
»

Содержание 35










































































Отзывы:

Нет отзывов

Похожие инструкции для 35

Бренд: UHV Design Страницы: 56

Бренд: F.F. Group Страницы: 44

Бренд: Makita Страницы: 80

EHR 20 / 2.6 S SET

Бренд: EIBENSTOCK Страницы: 64

Бренд: Cannondale Страницы: 12

Portable AC-to-DC Regulated Power Supply

Бренд: Radio Shack Страницы: 28

AXMINSTER Model Engineer Series

Бренд: Sieg Страницы: 28

Бренд: Jarvis Страницы: 12

Бренд: Bomag Страницы: 58

Бренд: F.F. Group Страницы: 32

NetSure 722NBBB

Бренд: Vertiv Страницы: 60

Бренд: Baileigh Industrial Страницы: 20

Бренд: Worcraft Страницы: 32

Бренд: Kerbl Страницы: 15

Бренд: Palmgren Страницы: 46

Бренд: iBell Страницы: 16

Бренд: BVV Страницы: 5

Бренд: Caswell Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды