Matrix S3X-02 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 64

Matrix S3X-02 Скачать руководство пользователя страница 18

15

8.4 TROUBLESHOOTING - DISPLAY ISSUES

NO DISPLAY ON THE CONSOLE OR THE DISPLAY IS DIM WHEN RUNNING

LED 1

LED 5

LED 9

LED 8

SYMPTOM:

The console will not power up or the display is dim.

CHECK POINT

POSSIBLE ISSUE

SOLUTION

LEDs 2, 3, 4, 6, and 7 should be ON.

If they are OFF, the LCB is damaged.

Replace the LCB.

If LED 1 is OFF.

No AC power cord plugged in.

Normal for an non-powered unit.

If LED 5 is OFF.

Generator has no RPM output.

Normal for a powered unit. If non-powered

and issue is still present, replace the

generator.

If LED 8 is OFF.

Bad communication between UCB and LCB.

Reconnect the console cable at the LCB and

UCB and check for kinks.

If LED 9 is OFF.

LCB is not providing 12V power to the UCB.

Replace the LCB.

SOLUTION IF LEDS ARE NORMAL:

1) If the LEDs are lit normally, replace the UCB and console cable.

2) if the issue is still present after the UCB and console cable are replaced, replace the LCB.

CHAPTER 8: TROUBLESHOOTING

«
...
16
17
18
19
20
...
»

Содержание S3X-02

































































Отзывы:

Нет отзывов