background image

x 2

3

1

2

x 2

180°

x 2

b

a

x 2

c

d

e

e

  

INSIDE

VIEW

STAGE 8

INSIDE

VIEW

INSIDE

VIEW

INSIDE

VIEW

THE DOOR IS FACTORY ASSEMBLED 
AS A 

RH DOOR OPENING

TO REVERSE THE ROLLER 
BLOCKS FOR LH OPENING 
SEE DETAIL BELOW (e)

OUTSIDE

FACE

RH 

DOOR

(AS FACTORY

ASSEMBLED)

LH 

DOOR

ANTI-CLOCKWISE = ADJUSTS DOOR IN

CLOCKWISE = ADJUSTS DOOR OUT

ANTI-CLOCKWISE = ADJUSTS DOOR DOWN

CLOCKWISE = ADJUSTS DOOR UP

LOCK

ANTI-CLOCKWISE

This stage is describing fitting of the Door Panel. 
To reverse the Door to a LH Door opening (e) remove the Roller block assembled to the door glass using the roller block key 
provided in the kit of parts and an adjustable spanner. Rotate the block to the opposite side of the door glass and re-fit.  

a

. Important - 

Fit the plastic threshold protectors to the Threshold track at either side of the Door opening.

b

.

 Load the door glass firstly onto the threshold protectors and door guide and then carefully guide the door up to the door roller 

threads and wind them through the door roller blocks fixed to the glass. 

c.

 Remove both the cardboard top track door roller guides by pulling the tabs and unfolding them away from the top track. 

d

.

 Adjust the door panel if required so that it runs parallel to the door opening by adjusting the Roller blocks on the inside of the door. 

To adjust the door away from the top track rotate the central set screw clockwise using the 4mm allen Key. To adjust the door to the 
top track, rotate the central set screw anti-clockwise. 

d

.

 The door glass can also be raised or lowered by the adjustment screw in the top of the roller block using the 3mm allen key 

supplied. Rotate clockwise to raise the door, rotate anti-clockwise to lower the door. 

d

.

 

Lock

 the adjustment by rotating the set screw anti-clockwise

 

in the bottom of the roller block using the 3mm allen key supplied.

 

TO CHANGE
ROLLER 
BLOCKS
TO LH DOOR 
OPENING.

DO NOT 
OVERTIGHTEN

Содержание One MOSC1000
















Отзывы: