MasterCraft 055-0216-8 Скачать руководство пользователя

Страница: 55 / 62

headline bars

Engine is running
but no AC output.

Poor cord connection

Check all connections.

Circuit breaker is open.

Reset circuit breaker.

Faulty brush assembly

Replace brush assembly (Service
Centre).

Faulty AVR (auto voltage
regulator)

Replace AVR (Service Centre).

Loose wiring

Inspect and tighten wiring connections.

Other

Contact the help line.

Engine hunts or
falters.

Engine governor defective

Contact the help line.

Dirty fuel valve

Clean the fuel valve.

Carburetor is dirty and running
lean.

Contact the help line.

Choke in wrong position

Move choke until it stops under RUN
position or push in completely.

Repeated circuit
breaker tripping.

Overload

Review load and adjust. See “Do not
Overload Generator” (page 29).

Faulty power cords or device

Check for damaged, bare or frayed
wires. Replace defective device.

Circuit breaker still too hot

Let unit sit for 5 mins.

TROUBLESHOO

TING

Содержание 055-0216-8































































Результаты поиска

Содержание 055-0216-8

Отзывы:

Похожие инструкции для 055-0216-8

Бренды по названию

Популярные бренды

MasterCraft 055-0216-8, Инструкция по эксплуатации

Результаты поиска

Содержание 055-0216-8

Отзывы:

Похожие инструкции для 055-0216-8

Бренды по названию

Популярные бренды