Mastercook KGE 3415ZLX DYN, Инструкция по эксплуатации

Страница: 54 / 60

53
english
11.1 General tips
The electronic programmer (11.1.1) controls the operation of the
oven. It generates an alarm signal and automatically turns off the
oven after each completed cooking programme.
Programmer buttons:
- programmer function button
- time increase button
- time decrease button
Programmer symbols:
AUTO
- Automatic operation symbol
- Oven on symbol
- Timer symbol
After plugging the appliance into the ma- 1.
ins, the
AUTO
symbol and the current time
0.00
lash on the display. (11.1.2). This is
an intermediate point between plugging
the appliance in and setting the program-
mer.
Set the current time irst. The time has to 2.
be reset after long lasting power failure.
The accuracy of the programmer depends 3.
on the mains parameters. It is therefore
recommended to periodically adjust the
time by comparing it with another clock.
11.2. Setting the current time
Press
– and
simultaneously; the dot symbol will start
lashing (ig. 11.2.2). Set the current time (e.g. 13:45) using
the
and
buttons (ig. 11.2.2).
New time settings will be saved in a few seconds.
11.3 Setting cooking duration
The oven will turn on immediately after entering the settings.
Turn function control knob and temperature control knob to
–
working positions (see ig. 10.2 and 10.3).
Press
–
twice;
AUTO
symbol will lash on the display and
the
DUR
(ig. 11.3.1) and
0.00
(ig. 11.3.2) symbols will be
displayed alternately.
Set your desired cooking duration (e.g. 2 hours) using the
–
and
buttons (ig. 11.3.3).
Symbols
AUTO
and
(11.3.4) and the current time (e.g. 13:45 )
will be displayed after the time has been saved.
After the set time (2 hours) has elapsed, the oven will turn •
off automatically. You will hear an alarm sound and the
AUTO
symbol will lash.
Press any button to turn off the signal. The oven will now be •
set to manual mode.
If the food needs more cooking, further operation of the oven •
must be controlled by the user.
If the food is ready, set the function and the temperature con- •
trol knobs in the off position.
11.4 Setting cooking end-time
This function is usually used together with the ‘cooking duration’
function in the automatic operation mode.
Setting cooking end-time:
Press
–
three times; the
AUTO
symbol will lash on the
display and the
END
symbol (ig. 11.4.1) and the current
time (ig. 11.4.2) will be displayed alternately.
Set cooking end-time (e.g.
–
17:00 ) using
and
but-
tons (ig. 11.4.3). Symbols
AUTO
(11.4.4) and the current
time (e.g. 13:55 ) will be displayed after the time has been
saved.
Note !
1. Your settings will be saved in about 5 se-
conds.
2. The alarm signal will go off automatically
after about 7 minutes if not switched off
manually.
11.5. Automatic control
Delayed start function is available in the automatic mode.
If you wish the appliance to operate for some time and turn off
automatically at a speciied time, set the duration of cooking and
the automatic turn-off time.
Programming :
set the duration of cooking according to section 11.3
–
set cooking end-time according to section 11.4
–
turn the function and temperature control knobs to wor-
–
king positions
EXAMPLE:
Beef roasting:
current time – 13.00
recommended roasting time – 2 hours
roasting temperature – 220
0
C
food to be ready at: 17:00
Place the meat in an oven-pan, add approx. 10 spoonfuls of •
water and cover the pan with a lid. Put the pan in the oven on
the selected level and close the oven door.
Set the function control knob to e.g. • and adjust the tem-
perature control knob to 220˚C.
Set the required cooking time (2 hours) and the automatic co- •
oking end-time (17:00).
The oven has now been programmed and the cooking process
will take place automatically. The programmer will display the
current time and the
AUTO
function will remain on. Cooking will
start automatically at
15.00
. The symbol will appear on the