DOWN EAST (3 -4 PUMP SYSTEMS) - CONTROLS
Jets 1
Touch the “Jets 1” button once to turn pump 1 on or off. If left running, and the pump will
automatically turn off after 15 minutes.
Jets 2
Touch the “Jets 2” button once to turn pump 2 on or off. If left running, pump 2 will automatically turn
off after 15 minutes.
Jets 3 (if equipped)
This button is used to turn the pump 3 on and off. If left on, this device automatically turns off after
15 minutes.
Light
Press the “Light” button to turn the light on and off. If left on, the light automatically turns off after
4 hours.
L.E.D. Light (if equipped)
Press the "Light" button to turn the light on and off. If you wish to change the “function” of the lights,
turn the lights off, then on within 5 seconds. If you wish to leave the lights in the same “function”
setting for the next use, turn the lights off and do not turn back on for at least 5 seconds.
Mode
Mode is changed by pressing the “Warm” or “Cool” button, then pressing the “Mode” button.
Standard mode
is programmed to maintain the desired temperature. Note that the last measured spa
temperature displayed is current only when the pump has been running for at least 2 minutes. “Std”
will be displayed momentarily when you switch into Standard Mode.
Economy mode
heats the spa to the set temperature only during filter cycles. “Ecn” will display solid
when temperature is not current, and will alternate with temperature when temperature is current.
Sleep mode
heats the spa to within 20°F/10°C of the set temperature only during filter cycles. “SLP” will
display solid when temperature is not current, and will alternate with temperature when temperature is
current.
Filtration
The circulation pump runs constantly for filtration and the ozone generator (if installed) will be enabled.
Freeze Protection
If the temperature sensors detect a drop to below 44°F/6.7°C within the heater, the pump(s) will
automatically activate to provide freeze protection. The equipment stays on until 4 minutes after
the sensors detect that the spa temperature has risen to 45°F/7.2°C or higher.
49
DO NOT DIVE.
SPA WATER MAINTENANCE - Schedule
For Spas without Eco Pur™ Filtration System
Day One
1.
Test and adjust total alkalinity if necessary to between 80 to 150 ppm using the pH / alkalinity
increaser or decreaser 1oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump
should be running on high speed during this time with the air controls closed.
2.
Test and adjust pH, if necessary, to within the range of 7.2 to 7.8 using the pH / alkalinity increaser
or decreaser, 1/2oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be
running on high speed during this time with the air controls closed.
3.
Test and adjust sanitizer level. Add chlorine following label directions to maintain a free chlorine
level of 1 to 3 ppm. If using bromine, adjust feeder to maintain a total bromine level of 3 to 5
ppm. Add bromine tablets to the dispenser if necessary, following label directions.
4.
Add a water clarifier following label directions. If the spa is equipped with an ozone unit, we
recommend adding an enzyme product in place of the clarifier, following the label directions.
5.
Use a small amount of defoamer only if necessary.
Day Two Skip
Day Three
1.
Test and adjust total alkalinity, if necessary, to between 80 and 150 ppm using the pH / alkalinity
increaser or decreaser, 1oz at a time. Wait 15 minutes, retest and adjust if necessary. The pump
should be running on high speed during this time with the air controls closed.
2.
Test and adjust the pH, if necessary, to within the range of 7.2 to 7.8 using the pH / alkalinity
increaser or decreaser, 1/2oz at a time. Wait 15 minutes, retest and adjust if necessary. The pump
should be running on high speed during this time with the air controls closed.
3.
Test and adjust sanitizer level. Add chlorine following label directions to maintain a free chlorine
level of 1 to 3 ppm. If using bromine, adjust feeder to maintain a total bromine level of 3 to 5
ppm. Add bromine tablets to the dispenser if necessary, following label directions.
4.
Add sequestering chemical, following label directions for maintenance.
5.
If necessary, clean water line with a spa general purpose cleaner or enzyme product.
6.
Use a defoamer only if necessary.
Day Four Skip
(cont. next page)
28
DO NOT DIVE.
Master Spa Parts - 1068 American Drive, Neenah, WI, 54956, USA
