Masdaf UKM-50 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 23

Masdaf UKM-50 Скачать руководство пользователя страница 2

EC DECLARATION OF CONFORMITY

AT UYGUNLUK BEYANI

Manufacturer / İmalatçı

: MAS DAF MAKİNA SANAYİ A.Ş.

Address / Adres

: Aydınlı Mah. Birlik OSB. 1.No’lu Cadde No:17 Tuzla - İSTANBUL / TÜRKİYE

Name and address of the person authorised to
compile the technical file
Teknik Dosyayı Derleyen Yetkili Kişi ve Adresi

Vahdettin YIRTMAÇ
Aydınlı Mah. Birlik OSB. 1.No’lu Cadde No:17
Tuzla - İSTANBUL / TÜRKİYE

The undersigned Company certifies under its sole responsibility that the item of equipment specified below satisfies the
requirements of the mainly Machinery Directive 2006/42/EC which is apply to it.
The item of equipment identified below has been subject to internal manufacturing checks with monitoring of the final assessment
by

MAS DAF MAKİNA SANAYİ A.Ş.

Aşağıda tanımlanmış olan ürünler için Makine Emniyeti yönetmeliği 2006 / 42 / AT’ nin uygulanabilen gerekliliklerinin yerine
getirildiğini ve sorumluluğun alınmış olunduğunu beyan ederiz.
Aşağıda tanımlanan ürünler içüretim kontrollerine bağlı olarak MAS DAF MAKİNA SANAYİ A.Ş. tarafından kontrol
edilmiştir.

Equipment / Ürün

: Self Priming, Single Stage Centrifugal Pumps

Kendinden Emişli, Tek Kademeli Atıksu Pompaları

Seri / Model-Tip

: UKM-S Series –

UKM-S Serisi

For pumps supplied with drivers/ Elektrikli Pompa Üniteleri
Related Directives / Yönetmelikler
2006/42/EC

Machinery Directive

/ 2006/42/AT Makine Emniyeti Yönetmeliği

2014/35/EU

Low Voltage Directive

/ 2014/35/AB Alçak Gerilim Yönetmeliği

2014/30/EU

Electromagnetic Compatibility Directive

/ 2014/30/AB Elektromanyetik Uyumluluk Yönetmeliği

Regulations applied acc. to harmonize standards / Uygulanan Uyumlaştırılmış Standartlar
TS EN ISO 12100:2010, TS EN 809+A1, TS EN 60204-1:2011.

We hereby declare that this equipment is intended to be incorporated into, or assembled with other machinery to constitute relevant
machinery to comply with essential health and safety requirements of Directive The machinery covered by this declaration must
not be put into service until the relevant machinery into which it is to be incorporated has been declared in conformity with
provisions of the directive.

Ekipman, uygun bir makina oluşturmak amacıyla diğer ekipmanlar ile birleştirilirken ya da monte edilirken gerekli sağlık ve
güvenlik yönetmeliklerine uyulması gerekmektedir.
Bu bildiri kapsamında yönetmelikte belirtilen bütün hükümler yerine getirilmeden makinanın devreye alınmaması gerekmektedir.

Place and date of issue /

Yer ve Tarih

:

İstanbul, 02.06.2014

Name and position of authorized person

Yetkili Kişinin Adı ve Görevi

:

Vahdettin YIRTMAÇ

General Manager / Genel Müdür

Signature of authorized person

Yetkili Kişinin İmzası

:

«
1
2
3
4
...
»

Содержание UKM-50
























Отзывы:

Нет отзывов