MASCOT MSTWW, Инструкция по установке и эксплуатации

Страница: 33 / 68

Mascot ST Tankless Water Heater Page 31
Customer Service and Product Support:
800.900.9276 • Fax 800.559.1583
Headquarters:
20
Industrial Way, Rochester, NH 03867 • 603.335.6300 • Fax 603.335.3355
1869 Sismet Road, Mississauga, Ontario, Canada L4W 1W8 • 905.238.0100 • Fax 905.366.0130
www.Laars.com
Customer Service and Product Support:
800.900.9276 • Fax 800.559.1583
Headquarters:
20
Industrial Way, Rochester, NH 03867 • 603.335.6300 • Fax 603.335.3355
1869 Sismet Road, Mississauga, Ontario, Canada L4W 1W8 • 905.238.0100 • Fax 905.366.0130
www.Laars.com
Litho in U.S.A. © Laars Heating Systems 1503 Document 4286
800.900.9276 • Fax 800.559.1583 (Customer Service, Service Advisors)
20 Industrial Way, Rochester, NH 03867 • 603.335.6300 • Fax 603.335.3355 (Applications Engineering)
1869 Sismet Road, Mississauga, Ontario, Canada L4W 1W8 • 905.238.0100 • Fax 905.366.0130
www.Laars.com
Document 4286
M
ascot ST Gas Conversion Kit
pg 4 of 4
Table C
Table D
Figure E (Conversion label)
25.
Once the CO2 and manifold pressure
measurements for both MIN and MAX Fire are
correct (for your altitude) turn OFF the Control
Display
and set DIP switches 6 and 7 to the
OFF position for Nominal Fire (normal operation).
Turn the Control Display back on when done.
26.
Write in the correct Conversion Date and the
Technicians Name to the included gas conversion
sticker. See Figure E. Then apply that sticker
adjacent to the rating plate.
27.
Put the water heater cover back on and assemble/
tighten the 4 screws that hold the cover in place.
This unit was converted on ____/____/___to _____gas
with kit #____________by______________________
(name and company __________________________
accountable)_________________________________
___________________________________________
Cette unité a été converti ____/____/____ten ______gaz
en utilisant le kit numéro _____ par______________
(nom et société_________________________________
responsable)___________________________________
_____________________________________________
WARNING
Always make sure that the Control Display is turned
OFF before changing any DIP switch. Then turn Control
Display back ON to continue with CO2 measurements.
High Altitude
Setting level
‘LP’ CO2
Values
‘NG’ CO2
Values
MSTWW199 2" or 3" VENT 2" or 3" VENT
0~2,000 ft
10.7 MAX 10
9.7 MIN 8.5
2,000~5,000 ft
10.2 MAX 9.1
10.3 MIN 9.7
5,000~8,000 ft
10.3 MAX 9.1
10.4 MIN 9.8
8,000~10,000 ft
10.5 MAX 9
10.6 MIN 9.8
AVERTISSEMENT
Ce conversion doit être installé par un organisme de
service conformément aux instructions du fabricant
et tous les codes et les exigences de l’autorité
compétente. Si les informations contenues dans ces
instructions n’est pas suivi à la lettre, un incendie,
une explosion ou de la production de monoxyde
de carbone mais résultat causant des dommages
matériels, des blessures ou des pertes de vie. Le
service est responsable pour la bonne et complète
l’installation de ce kit. L’installation n’est pas correcte
et complète jusqu’à ce que le fonctionnement de
l’appareil converti est vérifi ée comme
spécifi é dans
le manuel d’instruction fourni avec le
kit.
Manifold pressure ‘NG’ type combustibility ‘LP’ type combustibility
MSTWW199
MAX FIRE -0.11” to -0.17” WC -0.07” to -0.11” WC
MIN FIRE -0.10” to -0.16” WC -0.06” to -0.10” WC
H2373700-