MARLO MR M Series Скачать руководство пользователя страница 13

Страница: 13 / 52

MR 150M–1050M SINGLE – MXIII CONTROLLER

INSTALLATION

INSTALLATION INSTRUCTIONS

BRINE TANK INSTALLATION

The brine tank should be installed on a smooth level surface. If none is available, the tank should be placed on a

smooth piece of exterior plywood and leveled by placing shims underneath the plywood.

2. Make sure that the salt shelf inside the tank is level and that the brine well is near to vertical as possible. Check

the specifications table and make sure that the float setting is the proper height for the model provided. Brine

tanks are shipped with the float set for maximum salting. If incorrect, slide the float to the proper setting. Float

should be approximately one inch above grid plate.

3. Place brine valve into the brine well and set at the bottom of the brine tank. Note: If minimum brine draw is de

sired, remove the pipe nipple and coupling from the brine assembly. Install remaining brine valve assembly into

elbow using Teflon tape or Teflon paste, and set float to minimum salt level see Specification Table for settings.

Place brine valve into brine well. Brine valve assembly will not sit on bottom of brine tank.

Connect the brine valve to the brine injector. Open the manual injector feed water valve and allow the brine tank

to fill with water. To speed this process the tank can be filled with a garden hose to about 2” below the platform.

The tank will continue to fill until the float rises and shuts of the flow (approximately 1” above the platform).

Note:

In the process of making brine for the first regeneration, the solution volume will increase (one gallon of wa

ter will be 1.2 gallons of brine). The final level of the liquid will be several inches above the platform.

5. If the refill water shuts off below the platform or too far above the platform, the brine valve should be removed and

the float adjusted up or down until is shuts off approximately 1” above the platform. Place the brine well cap seal

in place and open the manual valve in the brine line to the softener tank.

TO INJECTOR

OVERFLOW

(PIPE TO DRAIN)

FLOAT

BRINE VALVE

LIQUID BRINE

DRY SALT

STORAGE

SALT SHELF

BRINE WELL

TO INJECTOR

TOP

EXTENSION

BRINE VALVE

FLOAT HEIGHT

FLOAT

Содержание MR M Series





















































Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды

MARLO MR M Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды