MARLO MR M Series Скачать руководство пользователя страница 46

Страница: 46 / 52

MXIII SINGLE PROGRAMMING GUIDE

MAINTENANCE

ERROR MESSAGE

CAUSE FOR ERROR

CORRECTION

Flashing Time

Power outage.

Program time by holding UP on Unit #1.

Detected Error = Matching Address

Two or more units programmed with the same

valve address number

Program each unit with unique valve address

number in Master Programming.

Detected Error = Program Mismatch

Master program parameters do not match

between two or more controls.

Confirm Master Programming for each unit.

Detected Error = No Message #1

No power to Control #1.

Power Control #1..

Communication Cable to Valve Address #1

bad or missing.

Connect or replace Communication Cable.

Detected Error = No Message #2

No power to Control #2.

Power Control #2.

Communication Cable to Valve Address #2

bad or missing.

Connect or replace Communication Cable.

Detected Error = No Message #3

No power to Control #3.

Power Control #3

Communication Cable to Valve Address #3

bad or missing.

Connect or replace Communication Cable.

Detected Error = No Message #4

No power to Control #4.

Power Control #4.

Communication Cable to Valve Address #4

bad or missing.

Connect or replace Communication Cable.

Detected Error = E2 Reset Unit

This message appears after a software reset.

Reprogram control using Master Programming

section.

Test Mode

Circuit Board was not programmed at factory.

Replace Circuit Board.

Black Squares on screen

Bad Circuit Board.

Replace Circuit Board.

INI on screen for more than 2 minutes

Circuit board not getting feedback from cycle

switch.

Inspect Motor - should be rotating.
Wire Harness disconnected.
Check Cycle Micro Switch.

CHG on screen for more than 2 minutes

Control programmed incorrectly as 2900 or

3900 valve type.

Reprogram unit as Stager Valve type.

ERROR CODES

If a communication error is detected, an Error Screen will alternate with the main (time of day) screen every few

seconds.

•

All units In Service remain in the In Service position.

•

All units in Standby go to In Service.

•

Any unit in Regeneration when the error occurs completes Regeneration and goes to In Service.

•

No units are allowed to start a Regeneration Cycle while the error condition exists, unless they are manually

forced into Regeneration.

•

When an error is corrected and the error no longer displays (it may take several seconds for all of the units in a

system to stop displaying the error message), the system returns to normal operation.

NOTE: During the error condition the control continues to monitor the flow meter and update the volume

remaining. Once the error condition is corrected all units return to the operating status they were in prior to

the error. Regeneration queue is rebuilt according to the normal system operation. Or, if more than one unit

has been queued for regeneration, then the queue is rebuilt according to which one communicates first.

Содержание MR M Series





















































Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды

MARLO MR M Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды