MARLO MR M Series Скачать руководство пользователя страница 48

Страница: 48 / 52

MR 150M–1050M SINGLE – MXIII CONTROLLER

MAINTENANCE

TROUBLESHOOTING CONTROLLER

EXAMPLE ERROR SCREENS

CAUSE

CORRECTION

A. Any or all of two or more units programmed with the same unit number

(Matching Address Error)

A. Connect the communication cables and/or replace.

B. Flashing/blinking display.

B. Power outage has occurred.

C. Format Mismatch (Units have both U.S. and Metric Formats)

C. Verify all units have same Format selected (all U.S. or all Metric)

D. No messages displayed/small black squares appear in display

D. Turn the contrast button on the back of unit until text appears (see “Prob-

lems Viewing Display/Changing Contrast of Display” below)

E. Size Error (Units not correctly numbered/more than one unit has the same

number assigned)

E. Check each unit and verify each as the correct number, and that only one

unit has that number

F. Com Error (Communication Error)

F. Check the wiring of the system and verify it is correct and that all are con-

nected

Detected Error

1. Go through Master Programming to program the unit.

No Message #1

1. Make sure all communication cables are connected.

2. If “No Message #1” ensure it is the lead unit.

3. Ensure #1 is configured for the correct system type.

No Message #3

1. Make sure all communication cables are connected.

2. If “No Message #3” ensure it is unit #3.

3. Ensure #3 is configured for the correct system type.

Program Mismatch

1. Ensure the units on the network are not configured the same as #1/the

Lead unit.

Exceed Unit Size

1. There are more units on the system than the Lead is programmed for.

Matching Address

1. The unit is programmed the same # as another unit.

NOTE: The rest of the system will still function without this unit.

Содержание MR M Series





















































Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды

MARLO MR M Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды