MARLO MR M Series Скачать руководство пользователя страница 33

Страница: 33 / 52

MR 150M–1050M SINGLE – MXIII CONTROLLER

OPERATION

9. Display Format

This program step is used to set the desired volume display format. This option must be the same on all system units.

U.S. will display volumes in gallons and is in 12 hour timekeeping. Metric will display volumes in liters and is in 24

hour timekeeping.
1. Use Up or Down buttons to adjust this value.

2. Press the Extra Cycle button.

10. Unit Capacity

This program selects the individual timer’s total capacity of hardness that can be removed. The unit capacity is

measured in grains if in U.S. mode and degrees in Metric mode.

U.S. Range: 9,000 to 9,900,000 Grains (Default = 300,000 Grains)
Metric Range: 90.0 to 199,000.0 grams CaCO

(Default = 300.0 grams CaCO

)

1. Use the Shift button to select the digit you want to modify.

2. Use Up or Down buttons to adjust this value.

3. Press the Extra Cycle button.

11. Capacity Safety Factor

This program step is used to adjust the capacity of the system. This is a percentage by which the unit’s capacity

is reduced.

Range:

0 – 50% (Default = 0%)

1. Use the Shift button to select the digit you want to modify.

2. Use Up or Down buttons to adjust this value.

3. Press the Extra Cycle button.

MASTER PROGRAMMING GUIDE

12. Feed Water (Hardness)

This program step is used to set the feed water hardness. The system will automatically calculate volume remaining

based on the Unit Capacity, Capacity Safety Factor and Feed Water Hardness entered.

U.S. Range:

1 – 199 gpg (Grains per Gallon)(Default = 15)

Metric Range:

2 – 199 grams CaCO

/Liter (Default = 30)

1. Use the Shift button to select the digit you want to modify.

2. Use Up or Down buttons to adjust this value.

3. Press the Extra Cycle button.

Содержание MR M Series





















































Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды

MARLO MR M Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание MR M Series

Отзывы:

Похожие инструкции для MR M Series

Бренды по названию

Популярные бренды