manualshive.com logo in svg

Markes International Unity 2, Руководство по установке

Поделиться
Скачать
Markes International Unity 2 Скачать руководство пользователя страница 7

 

 

 

QUI-1056

Page 7

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

1.5.3

 

Altitude 

The product has been evaluated for operation up to a maximum of 6500 ft (2000 m), in accordance with 
safety standards. Higher altitudes pose no safety risk, but instrument performance may be reduced. 

NOTE

:   For storage or shipping the allowable temperature range is -40 to 70°C and the allowable humidity 

range is 5-95% non-condensing. After instrument exposure to extremes of temperature or 
humidity, allow 2 hours for return to the recommended ranges before switching on. 

1.6

 

Technical Specifications 

1.6.1

 

Physical properties 

Height:  

40 cm (15.75”) 

Width: 

16 cm (6.3”) 

Length: 

51 cm (20”) 

Mass: 

16 kg (35.2 lbs) 

1.6.2

 

Electrical properties 

Maximum Power: 

650 W 

Line voltage: 

100-240 V (automatically selected) 

Frequency: 

 

50/60 Hz 

Input inrush current (A):  

<40 A (cold start) 

1.7

 

Technical support contact details 

In the first instance please contact your distributor. If they are unable to resolve your query, please contact 
Markes International (details below). 

Address:  

Gwaun Elai Medi-Science Campus, Llantrisant, RCT, UK, CF72 8XL 

Website:  

www.markes.com

 

E-Mail:   

[email protected]

 

Telephone:  

+44 (0)1443 230935 

Fax: 

 

+44 (0)1443 231531 

 

 

Содержание Unity 2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды