manualshive.com logo in svg

Markes International Unity 2, Руководство по установке

Поделиться
Скачать
Markes International Unity 2 Скачать руководство пользователя страница 11

 

 

 

QUI-1056

Page 11

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

3.

 

Installing UNITY 2 

3.1

 

Installing the Transfer Line 

UNITY 2 is supplied with a universal transfer line to convey desorbed analytes from UNITY 2 to a gas 
chromatograph or other analytical system. The sample path utilises a deactivated fused silica line 
(0.25mm I.D. and 0.35mm O.D.) heated over its entire length by means of a distributed heater and at the 
GC end by heat conduction from the GC oven. The heated transfer line is 1 m long, which is sufficient to 
reach most gas chromatographs even when a mass spectrometer is attached. 

NOTE

:  The parts supplied can be used in other combinations to suit particular instrument configurations. 

3.1.1

 

Installing the Transfer Line onto the GC 

There are two options for transfer line installation, one requires use of a hole in the top, side or back of the 
GC oven, while the other option is to gain access via an unused heated injector port. 

Option 1 – Through Hole in Oven Wall 

1.

 

Locate a hole in the inner oven wall with a corresponding hole leading to the outside of the 
instrument. 

2.

 

Where necessary, displace the oven insulation material such that the transfer line heater can be 
fitted directly against the external face of the oven wall. 

3.

 

Place one of the washers provided in the UNITY shipping kit on the external face of the oven wall, over 
the hole through which the transfer line will be passed. 

NOTE

:   A number of different washers are provided.  The washer required will be determined by the 

hole in the oven through which the transfer line will pass. 

4.

 

Fit the GC end of the UNITY transfer line through the hole in the washer and on through the hole in 
the GC oven wall. 

 

 

5.

 

Place a second washer over the UNITY transfer line so that it can be secured against the inside wall of 
the GC oven. 

Oven wall 

Oven wall 

Содержание Unity 2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды