manualshive.com logo in svg

Markes International Unity 2, Руководство по установке

Поделиться
Скачать
Markes International Unity 2 Скачать руководство пользователя страница 25

 

 

 

QUI-1056

Page 25

Markes International Ltd 

T:

 +44 (0)1443 230935   

F:

 +44 (0)1443 231531   

E:

 [email protected] 

 

www.markes.com 

4.

 

Software 

4.1

 

Installing the software 

Ensure that your PC meets all specifications presented in Section 2.1.  It is advised to close down other 
applications on your PC while loading UNITY 2 software. 

Locate the Markes TD software CD supplied in the shipping kit (

QUS-1000

).  Insert the CD into the 

appropriate compartment of the PC and follow the instructions on the screen.  Alternatively, open 
Windows Explorer (located under Start > Programs) and access the CD drive.  Open the Index.htm file 
located in the HTML_FILES folder. 

Markes TD Software will installed in C:\Program files\Markes TD (or C:\(x86)Program files\Markes TD for 
64 bit versions of Windows 7).  A shortcut to the Maverick.exe file located within this folder should be 
placed on the desktop for ease of access.  

4.2

 

Running the software 

Ensure that the gas supplies to the system - especially the dry air or nitrogen purge gas used for UNITY 2 
valve actuation and purging the cold trap box - are on. 

Having checked the above, switch UNITY 2 on using the switch located on the back panel of UNITY 2.  
Start the software by double clicking on the Maverick.exe file. 

If communications between the PC and UNITY 2 are established successfully the software will open.   

If for some reason, communication is not established an ‘Instrument not Detected’ box appears with a 
number of options, Cycle Power and retry? Run simulation? Select options? and Exit? 

 

 

 

Choose Select Options.  This will take you to Configuration tab of Options under the View menu.  Ensure 
that the Instrument Configuration is set to UNITY (manual) and that the correct PC communications port is 
selected.   

Содержание Unity 2





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды