manualshive.com logo in svg

Mark MEGAFLEX, Техническое руководство

Поделиться
Скачать
Mark MEGAFLEX Скачать руководство пользователя страница 34

34

6  

INSTALLATION

6.1 Installing the boiler

The installation must be done in accordance with all local and national codes, regulations and standards, 

and in accordance with the directives of all relevant authorities.

1.  The boiler must only be installed in an area where it is allowed to install it. Make sure that this area is 

protected against the danger of freezing.

2. 

The area should have sufficient ventilation and cooling to prevent overheating.

3. 

When delivered the boiler is on a pallet. Install the boiler on a flat non-combustible floor and level it 

by using its positioning bolts.

4.  A minimum free space of 50 cm should be left on each side of the boiler for service access.
5.  Remove the sealing/protection caps from the connection tubes. Warning : take care as residual water 

from testing may drip

6. 

Fill the condensate trap with clean water. This can be done by flushing some water into the cast alu

-

minium exhaust connection from the rear. This water will then drain into the syphon and fill it.

6.2 Frost protection

The boiler is protected against frost.

If the boiler detects an NTC flow temperature below 8 ºC, the CH-pump will be activated. If tempe

-

ratures continues to fall the boiler will start at a flow temperature of 6 ºC and it will run on minimum 

load until the flow NTC senses a temperature of 15 °C. The CH-pump will stay running for another 

10 minutes. 

This only protects the boiler and does not protect the installation, pipework or 

radiators against freezing.

During longer periods of absence in the winter, the installation itself should be protected by activating 
the heating periodically and by partly opening the radiator valves. Where a room thermostat is control-

ling the demand, do not set the room thermostat to a value below 15 °C.

To protect frost sensitive radiators against frost it is possible to connect a frost thermostat in parallel 

with a Volt free room thermostat.
It is also possible to set the CH pump to activate automatically under OTC settings when an outdoor 
sensor is present (this must be set by the installer). In this case,the CH pump will be activated if the out-

door temperature drops below 8 ºC. 

Содержание MEGAFLEX



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды